Calvin Grannis' 1974 TR6 with LS1 (project diary)

Started by 74ls1tr6, November 10, 2007, 11:32:59 AM

Previous topic - Next topic

74ls1tr6

Maybe I was thinking double ended double D? What would be done with the other end of the shaft if cut, spline, slip, weld if it is a solid shaft or..?

IaTR6

I think you use a double D joint, and cut the shaft to length, just like you did with the tubing. The difference is you wouldn't need to weld in spline stubs. I think the phasing of the joints wouldn't be an issue-but I haven't done it.
Dennis

IaTR6

Calvin,
Now that I look, I can see where if you used Woodward, the .750-20 spline stub would be necessary as Woodward doesn't seem to offer a 9/16-36 spline to 3/4DD shaft! DUH on me!
Dennis

74ls1tr6

I knew there was a method to my madness, and Dennis you figured it out! Thank You :-)

rficalora

For future reference, I'm pretty sure Sweet Manufacturing told me they'd make whatever configuration steering u-joint I wanted.  I'd already bought my u joints with the 34 or 32 or whatever spline my MG had and called them to order the steering shaft when I learned that.  Would be easier though to get one side of the u-joint with the spline you need for your column and the other side double d.  Same at the other end.  Then you can cut the shaft to fit.

Med72

Calvin:

Thanks, thats a great ideas.  This beats using a tape measure.  One additional question.  I noticed you put a indention on te left fender ( I figure 30 to 45 degrees) to allow for the shaft to pitch downward.  Did you cut out a portoion of the fender or did you just take a hammer to it?

74ls1tr6

Hi Art,

I cut out the inner fender a little then welded that little section in with the shape of the shaft for the clearance needed.

Phil Crawford

Calvin
I used the double D and cut to length and they seem to work OK but the Over size Heim joints on both sides of the double universal have a fair amount of slop around the shaft and you can see and feel it when moving the steering wheel.  Did you have that problem with the tubes  and if so have you done anything about it.  I haven't driven the car yet but getting close and would like to fix this problem now rather than later.  I have enjoyed your build and have used it as a reference many times.
Thanks
Phil

74ls1tr6

Hi Philip,

Nice build by the way Philip. I like the wood work that you have done among many other artful tidbits.

Hmmm, My steering shaft has very little movement inside the Heim joints, there is some but not enough to cause to much movement. What is the finish of your shaft? Can you weld some metal on the shaft and lathe it off for a closer tolerance in the area of the Heim joint? Maybe have some plating added on to take up the slack......I wonder if the tube I used had a little larger OD diameter that the double D shaft? I will mic out the OD of my steering shaft if I can get in there, for a measurement, and post up soon.

Rob,

That is a great reference for everyone that (Sweet Manufacturing) needs custom steering shaft or shafts made up.

IaTR6

Just a thought, and I haven't taken the time to research it, but could a speei-sleeve over the shaft take up the clearance to make it a snug fit? I presume there is no movement along the length of the shaft. I don't know how you would retain the sleeve-perhaps a thread locking material, or one of the bearing setting compounds?
Dennis

74ls1tr6

Hi Philip,

My OD on my steering shaft is .751....... the 1 thousand could be the sharks hide I put on there so it wouldn't rust....which is worn off in the Heim area. So probably an even .750 for OD. Do you have a measurement of the inside diameter of the Heim joint? I have a 1/4" play in my steering wheel from left to right sitting still. I need that play because of the Quick Rack that I'm using. A little touchy at high speed, so the little play that I have helps. I think that play is on the rack and pinion though. If I grab ahold of the double universal joint, move it in all directions, it has some play in there, but very little. Question? Are you using the original steering column? If so, did you replace the bushings inside (two)? Can you make a video of what it is doing, and post it up on youtube?

Dennis,

That Speedi-sleeve might work, but may need to press in a small pin, into the main shaft on both sides to hold into place.

IaTR6

I found a speed-sleeve listed to fit a shaft .748 to .752 that is part # 99076. The sleeves add .011 to the shaft diameter, which would have made Calvin's O.D. .763 I think. ( fits .752 and adds .011 = .763??) You could slip a feeler gauge between the shaft and the inside of the heim joint to see what play there is. Also, the speed-sleeve site listed Loctite RC-620 retaining compound to hold the sleeve on a shaft. This would prevent having to drill into or through the shaft.
Am I nuts or what?
Dennis

74ls1tr6

Dennis,

You're not nuts, you follow through with your research and think out of the box.

How is your project coming along?

IaTR6

Calvin,
The project is coming along, slowly. I must think a lot before doing some of the changes as I don't know what i am doing. I had a hotrodder say to cut out the entire firewall, set the engine in place, and construct around that. Probably good advice, but I was hesitant, and have done picemeal mods. The tub was worse than I thought, so patch repair on sills was ultimately scrapped, and all new installed. Geez Louise!
Current research on paint removal (media, stripper, recycled glass etc.) The tub is ready to stand aside while I check the frame for usefulness.
Thanks for asking! Oh, are you going to Omaha?
Dennis

IaTR6

Ed Peppard: I am interested in your chassis modifications that adapt the Ford 5.0. I am involved in a similar project, and see that you have done exactly what I am planning. Apparently you are not moving the engine back too far, but are lowering it in the frame. Do you care to elaborate? You may PM me if you wish.
Thanks,
Dennis

74ls1tr6

Hi Dennis,
I will not be attend the Omaha meet this year! I would love to, but have other plans.

Here is a video of the fastest time at Triumpest 2012 autocross at Flagstaff AZ. We had to sweep a ton of gravel off the turns when setting up the autocross track. Happened to do some drifting on my third run which killed my time on the long right hand turn. Tons of fun!!

<iframe width="640" height="360" src="https://www.youtube.com/embed/n0noi6_RlVM?feature=player_detailpage" frameborder="0" allowfullscreen></iframe>

Here is the same run from inside the car! The red TR250 of Andy Packards in the still frame (on the track), who is very fast with autocross tires, I was able to beat his time with my street tires. What a rush it is on the track! I don't have much time on an autocross track, 3rd time track running for me, but someone with more time in the seat would do better than me I'm sure.

<iframe width="640" height="360" src="https://www.youtube.com/embed/hF5cJeHk2PE?feature=player_detailpage" frameborder="0" allowfullscreen></iframe>

dwtr6v8


74ls1tr6

Hi Don,

"Yes" used my Go Pro Hero II Camera for the video in the car. Brenda was using our Sony projection on the wall type/flip out screen video camera. They both take great video!

Phil Crawford

Calvin and Dennis
Sorry about being slow getting back to you guys have been doing other things around the house.  Just to eliminate where the slack in the steering was coming from I made some bamboo wedges and drove them between the flat spots on the DD shafts and the heim joint.  This caused the outer race of the joint to turn but it took all of the slack out of the steering.
I don't have a I.D. heim measurement.  I wonder if a 3/4" heim joint would work? I could sand the shafts if they were too tight.  I don't think the out side race is supposed to turn.
I have never heard of a speed-sleeve.  Where do you get them?
Thanks for the information and your thoughts.  In the real world of hot rods this is the way problems are solved.  
By the way Street Rodder magazine calls out cars (Sport Rods). Imagination that..
Thanks again
Phil

IaTR6

Phil,
Here is one link I found to the manufacturer and catalog. I believe that SKS, a bearing manufacturer, and Chicago Rawhide, a company I thought made seals, are one company. Anyway, their catalog is where I found the information about speed-sleeves. They are used in many cases of shaft wear at the seal contact point, and renew the sealing surface to allow continued use of the mechanism without replacing the more expensive shaft. (No sales pitch intended!) I just though that using one of them might take up the clearance that was problematic for you.
Dennis
http://www2.chicago-rawhide.com/faq/1.html

Moderator

That's SKF. Biggest bearing company in the world. Roughly twice as big a company as Timken. S for "Svenske", I believe. Volvo was started by SKF and then spun off onto its own. Evidently SKF bought (comparatively tiny) Chicago Rawhide in the nineties...
1971 MGB GT V8
Buick 215 w/ Rover heads, custom EFI & crank-fired ignition.
Custom front and rear coilover suspensions.

IaTR6

Thanks Curtis! The PC I had couldn't spell worth a hoot, and my daughter promised this Mac would be better-NOT!
Dennis

Phil Crawford

Dennis
Thanks for the info. I will take a look and make a decision.  I wonder how a 3/4" heim would work?  You could always sand the shaft a little.
Thanks Phil

74ls1tr6

Philip,
I used a 3/4" heim in both spots on my setup.

Phil Crawford

Calvin
Thanks for the info.  I order 2 3/4" hiems yesterday plus the column bushings. I hope this is the last time I have to pull it out. I have been riding around some with loose seats and no belts. The DBW throttle  does not fly open from a dead stop like a manual one but it comes on pretty quick.  Really makes for a nice start but when it hits 2 ed it gives you gives you about 3 seconds of wheel spin. Impressive for a truck engine. I know you have had fun with your ride and have enjoyed the videos.
Thanks
Philip