Did a compression test on my stroked Olds 215, not good. #4 cylinder at 50 lbs.

Started by Gswest236, April 24, 2025, 09:43:55 PM

Previous topic - Next topic

Gswest236

Jim, Is there a downside to trying a start-up without the cooling system attached? I'm thinking that if it starts, I'd let it run for 10 seconds or so.

mgb260

I've only made sure everything is right and just started and ran it.

Gswest236

My worry is that being my first engine rebuild, I may have missed something and by at least getting it to act like it wants to run; I'll be confident enough to install the rad and the exhaust and go for a break-in. 

Gswest236

I primed the oil pump again, got the distributor back in and went for a start-up. Power on but no starter. Looked at my wiring and realized I had a starter wire off. Got that sorted and tried again; this time it turned over but backfired. Tried again and it turns over, getting fuel but no start up. It did fire a couple cylinders so I'm guessing I'm 180 degrees off on the timing. Tomorrow I'll pull the plugs and rotate until I know I'm TDC compression and try again.

mgb260

Scott, Pull the distributor and #1 spark plug. You don't need to pull any other plugs. Put a breaker bar and socket on crank bolt, turn slowly clockwise with your finger in #1 spark plug hole and when it blows out, you will be close. Set timing mark at crank by moving crank pulley until it lines up with 12 degrees. Use your priming tool to line up the oil pump slot with your distributor lined up pointing at #1. Make sure your wires are the right firing order. Tighten the distributor bolt snug but so you can still turn the distributor. Turn the key to on and wait a few second to fill the carb float bowls, then pump the linkage a few times to squirt gas into the engine. Should start right up.

Gswest236

Thanks Jim. I think its got spark and fuel, so timing is the issue.

Gswest236

I went at it again today by getting it to TDC compression using the finger method. Set the timing mark at 12 degrees. Got the distributor in pointing at #1. It started! Running rough but it ran and definitely needs timing adjustment to get it to smooth out. Oil pressure was well over 50 lbs.  I have a timing light thats old but I'll deal with that after getting the rad in and the exhaust in. It's a loud beast on straight headers! Thanks for the help!

mgb260

Scott, Best way to time is full advance first. You don't have to worry about plugging vacuum advance line as your MSD distributor doesn't have one. Take it up to 4000 RPM after you have the cooling system hooked up. You want 32-36 Total timing normally and it is what it is initial. If you have a starter kickback drop it 2 degrees. With that cam and today's gas, I think you will end up around 32 total and around 12 initial depending on what advance your distributor has.  Adjust your carb mixture screws by starting 2 turns out and slowly turn in until you hear RPM drop, then open 1/2 turn. You may have to adjust the choke too.

Gswest236

Thanks Jim! Timing is completely Greek to me. Never checked timing, never set timing, never used my timing light once. So, I will heed your advice when I get to that point. In the meantime I have to connect the cooling hoses, get some coolant, install the exhaust, and then go for tuning the carb and timing the ignition. Little by little, we're getting there. Thanks!

Gswest236

A tool I didn't know I needed until I needed it, Distributor hold-down bolt wrench. I bought a set of HF crow feet wrenches thinking that's what I needed, that was a no-go. 

Gswest236

Exhaust went on today. The ceramic coating on the headers made for a very tight slip on fit, but sand paper and WD40 made it happen. Waiting on a thermostat housing gasket to get the Rad filled. And of course the crappy timing light I have doesn't reach the battery so I'll have to extend it.

MGBV8

I power my timing light from the back of the Delco alternator.  Using the battery in the stock location would be a PITA.
Carl


Gswest236

Got the upper rad hoses on, no problem. The lower hose used the space formerly created by the oil filter swivel mount. Now that that's gone and we're back to the stock oil filter position,  we have to do a re-route. Not a big deal, just need a little bit longer 90 degree 1.25" hose. O'Reilly's here we come, again!

Gswest236

I got the coolant in and went for a startup. I got it running and advanced the timing until it smoothed out. Adjusted the carb until it seemed happy. But there is some chatter on the passenger side valve cover which also leaked a small puddle of oil. I tightened it up but I think I'll take that cover off tomorrow and see if something obvious is going on. Strangely the oil pressure was pegged on the dial at 100 lbs?? First start up it was 55 lbs but it wasn't idling so I shut it off since there was no coolant in it. Today It never got to 180 degrees so the thermostat didn't open. I ran it maybe 3 or 4 minutes twice and then noticed the oil leak. So the concern is the Right side noise, the extreme oil pressure and then of course the oil leak. Never seen a valve cover leak that bad but with 100 lbs oil pressure I guess It could have forced it out at the weakest point. When I saw the leak, I thought maybe the oil passage repair failed, but there's oil around the spark plugs on the right side which is above the repair. Oil is sitting in the frame rail channel on that side which seems like it could only have come from the valve cover seal.
Edit: I'm reading that the oil pressure relief valve may be stuck or has too stiff a spring.

mgb260

Scott, do you have an adjustable relief valve? If not the relief valve spring may be too long or relief valve is sticking. I usually use the 60lb spring. Common for new build first start to have around 70-80 psi cold but gradually drop as it warms up. You are using 10-30 and not 20-50 right?

https://www.v8buick.com/index.php?threads/oil-pressure-concern-412.347470/#post-2953683

mgb260

Scott, You have the newer Metric cover, or "B" in the link above. Relief springs are shorter than the old style pump "A". Should be yellow for 60lbs or orange for 40lbs relief. If using the longer spring that is the issue. The clatter you will find when you pull the valve cover.

Gswest236

Thanks, I'm taking the valve cover off today to see if anything's loose. Next I guess I'm getting into the oil pump. Pretty sure I used the spring that came with the pump, but we'll see what's in there or if it's stuck.

mgb260

The oil pump gear kit usually comes with an assortment of springs. Some have cut the old style spring so it sticks out about 5/8".

Gswest236

It's bad! Most of the pushrods are bent, some are subtle and others are not so subtle. I have a broken rocker on the left side and a spring on the right side is about to come off on the rocker assembly. So, I'm assuming that means the cam and lifters are damaged as well? Are my pushrods too long or is it something else? I guess the motor is coming back out!

mgb260

Scott, Just pushrods bent on that one side? Those pushrods should not be too long unless they sent you the wrong ones. Maybe the 100+psi oil pressure pumped the lifters up like solids? I wouldn't pull the motor. Probably just need to replace pushrods and fix rocker issue; Check your oil pressure relief spring. Before you order new pushrods, get an adjustable one to check for correct pushrod length.

mgb260

Those pushrods should only be .009 longer than original. 8.245 vs 8.236. Could you measure one that appears straight?

mgb260

Scott, I remember you were confused on the timing gear setup, are the pushrods that are bent all intake or all exhaust. If you have the timing setup adv or retard too far the valves can hit the pistons and bend valves and pushrods. Too far advanced would be intake, too far retarded would be exhaust.

Gswest236

OK, there are bent rods on both sides. I compared the new pushrods to the old ones and they were the same or probably within the .009 as you mention. I'll see if the bent ones are all exhaust or intake tomorrow and get back with you. The motor was running rough and I advanced the timing (initial was set 12 degrees advanced) and it smoothed out, so I locked it there. It was idling fine, just noisy.  Just reading online I'm seeing things like Valve spring coil bind as a possible reason. When I initially turned the motor over by hand (before actually starting it) there were no interference issues. Valve train geometry issues are also mentioned when you search bent pushrods. I'll measure one of the straight pushrods and post a pic of one of the bent ones.
It's also mentioned that the cam could be damaged when you have severely bent pushrods.

mgb260