LS4 Into an MGB

Started by Scott Costanzo, October 22, 2013, 09:12:39 PM

Previous topic - Next topic

74ls1tr6

Scott,

Keep going you are making good progress. The exhaust is a exhausting process for sure. You now will feel everthing will move faster. Can't wait to see first start up video. This will put a big smile on your face for all your labor involved. :-)

Scott Costanzo

QuoteCan't wait to see first start up video. This will put a big smile on your face for all your labor involved. :-)

Thanks Calvin. If I can catch a couple of breaks, I hope to experience that event sometime in June. :)

Scott Costanzo

Wiring is well underway now. Here is a front shot showing the current status.

LS4FrontWiringHarness.JPG

Here are a couple showing both sides.

LS4PassSideWiring.JPG
LS4DriveSideWiring.JPG

The injectors and coils are all wired up. The TPS, IAC, MAP, and crank sensor wires need to be shortened. Still need to wire up the MAF, cam sensor, O2 sensors and knock sensors. Of course a fuse box will be needed to power everything like the PCM, injectors, coils, fuel pump and O2 sensor heaters. The alternator will be mounted on the passenger side and that wiring will be added to the passenger side as well. I've got some high temperature wiring harness wrap that I'll use on everything once the harness is done. It's really starting to look like a part of the car now, if you know what I mean?

kstevusa

Scott, your work looks great!  I'll drink a DIckel & 7-Up  just to toast your craftsmanship!.   Guess Arite will have to wait also.  Until we meet again:-)

Scott Costanzo

Thanks Kelly! I'm all in for some Dickel & 7! :)

Scott Costanzo

Spent most of yesterday at the junkyard so didn't get a lot done wiring wise. Got some terminals for the fuse box I'm using and several plugs that were missing.....O2 sensor, knock sensor,  and alternator. Also got an alternator mount from a V6 car that will be adapted to the LS4 and picked up a throttle cable and throttle pedal too. I'll go into more details about these things later on. Of course I forgot something even though I had it on my list...OBD2 data link connector, oh well.

Did get something accomplished though, pretty much finished the throttle body adapter. Here's a picture of the throttle body in place.

LS4ThrottleBody.JPG

Here's one with of the adapter plate itself.

LS4ThrottleBodyAdapterPlate.JPG

I realize it's not perfect...the whole build is "blue collar" to some extent, especially compared to what Calvin and Brenda are doing, but I'm not taking the time to make things perfect. What is there will work and that is what is important to me at this point.

Just about everything is in here now so the wiring can be completed. For the next couple of sessions that will be the focus. I'm going to take Jim Stabe's suggestion and go with the F6 wiring loom stuff. Should look good.

mgb260

Scott, You're making steady progress! I'm looking forward to the water pump/front pulley solution. You will be starting it up before you know it!

Scott Costanzo

Made some great progress last weekend but not much you can really show with pictures at this point. Here is one that shows the completed wiring at the front of the motor.

LS4WiringHarnessProgress.JPG

Except for the O2 sensors VSS, and knock sensors, all the engine controls/sensors are wired. Next on the list is getting the fuse box squared away and the grounds securely bundled and bolted to the block. Here's a picture of the fuse box that will be used.

LS4FuseBox.JPG

The engine harness itself will be pretty much stand alone when it is complete. Power to the fuse box will come off the starter solenoid for those components that require power when the key is off and from a white wire on the B harness for those components that require key on power like the injectors, coils, and fuel pump. The alternator warning light will be wired to the alternator plug, the engine speed output from the PCM will be wired to the tach and the B coolant temperature sensor will mounted and wired into the passenger side head. That's pretty much it as far as the interface to the existing harness is concerned, not counting the wiring to the starter. Hope to have more pictures and details as progress is made.

MGBGT?

Hey Scott,
Really nice work!  You've got some talent!
I was wondering about how you were going to get filtered air into the throttle body.  May I suggest moving the radiator forward & tilting it back just like a late C4 Corvette, then use a late C4 Corvette air cleaner box.  It's specially designed for hood clearance with an oval intake over the radiator support as per the attached photos.
DSCN0108.JPG
DSCN0109.JPG
DSCN0110.JPG

Scott Costanzo

Hey Artie! Glad you're here and thanks for the complement! Thank you for the suggestion as well! I'm actually moving in that direction.

I have three main goals in mind for this project; no modifications to the bonnet (hood for you Corvette guys :-) ), keep the steering rack in the stock location, and the radiator pretty much in it's current location. So I'm really going to be working to avoid moving the radiator forward. What I'm planning longterm is to fabricate a fiberglass snout very much like what you are suggesting which will go over the radiator and then fabricate an air box for a flat air filter in front of that....with the MAF in the middle...kind of hard to put into words. I'll be lowering the radiator about an inch. This will be an early phase 2 task though. For the short term, I'll use a rubber duct of some sort and a cone air filter. Won't look great but it will duct clean air to the engine. That's the plan for now.

On another subject, the wiring harness is ever so close. Hope to finish and get some pictures up soon.

Take care

Scott

Scott Costanzo

Looks like you've been cleaning your engine again! :)

74ls1tr6

Hey Scott,

I have the air cleaner somewhere that I got off the Camaro Ls1 from the Tr6. I will find it measure and post some photos of it. Maybe you can use it for the cost of shipping? It is setup like you had mentioned in your plan. Maybe you can make it work somehow. I believe I have the ducting that goes with it too.

Scott Costanzo

Hi Calvin,

If you have the time I'd love to see some pictures. Definitely interested if it looks like it could work.

Thank you!

Scott

MGBV8

I really like the over the radiator snorkle approach.
Carl

Scott Costanzo

QuoteI really like the over the radiator snorkle approach.

So do I Carl. It's going to be really tight though. It would be easier with the MAF behind the radiator so I'm thinking that I need to get an LS1 or LS6 manifold first as they place the throttle body further back. Again, this will be a phase 2 task.

Didn't get too much time to work on the car, it's the wife's birthday weekend. I did get the F6 stuff and started installing it on the harness. Here are a few pictures.

LS4Conversion 068.jpg

LS4Conversion 070.jpg

I really like the look and it's pretty easy to install too. You have to melt the ends once you cut them as it looks like the material could unravel. One other benefit is it comes apart easily if you need to get into the wiring for some reason.

The mess you see on the left in the second picture isn't nearly as bad as it looks. Everything is labeled and, for the most part, ready. The fuse box connectors are done except for the cooling fan relay signal from the PCM. Just need to put the connector on it. Also, the OBD2 connector power needs to be run to the fuse box as well. Other than that, 4 or 5 miscellaneous tasks need to be completed and the wiring should be done. I hope to get the motor ready to pull by the end of next weekend with a little bit of luck. Next up is putting the firewall back together.

74ls1tr6

Scott still looking for the air box!

Scott Costanzo

Calvin, absolutely no rush at all. Please don't take time away from what you need to do for this.

Thanks!

Scott

74ls1tr6

Ok Scott,

Have some photo's of the air cleaner box off a 2002 Camaro Z28. Also have some of the throttle body tube, and if you need one a computer holder.
By the looks of the air cleaner box you could trim down the sides and it could be usable? Looks like it hangs on the radiator top?

2014-05-07 07.36.40.jpg


2014-05-07 07.36.57.jpg


2014-05-07 07.37.28.jpg


2014-05-07 07.37.40.jpg

Scott Costanzo

Calvin, you have a PM!

mgb4tim

Something like an airbox is the kind of stuff I'm going to enjoy making with my fiberglass experience.

Scott Costanzo

Haven't been posting because there wasn't anything new to report. Still making steady progress.

The wiring harness is, for all intents and purposes, done. What remains is better done with the engine out of the car. As anyone who has done something like this before knows, there are a million details to deal with...all part of the fun in projects like this.

I use the original gauges and I was planning on drilling out a head to accommodate the "B" temperature sender. Fortunately, I came to my senses before making that stupid move. What I did was chucked the sender in my drill press, turned it down to the correct diameter, and threaded it to fit into the existing hole at the back of the passenger side head. This picture shows the LS temperature sender along side the "B" unit. The thread is 12mm X 1.5, FYI.

LS4TemperatureSensors.jpg

This one shows it in the head. I needed to make sure it was going to fit correctly before pulling the engine to put the firewall back together.

LS4MGTempSensorInstalled.jpg

So I'm making slow but steady progress on the firewall. I'm tackling the hard side first and expect the remainder is going to go more quickly. You can see my approach in the photo below.

LS4FirewallStart.jpg

I spent a lot of time measuring and fitting the steering column before welding things together and I'm going to tweak what you see here a little more before finishing that side. I'm using 16 gauge steel if you're wondering. I'm working now to finish the engine compartment completely. That includes finishing the firewall, cross member, running new brake lines, finishing the motor mounts, and mounting the steering rack and steering shaft. Hopefully another few weeks will do it.

One other bit of news is the car won't be ready for Colorado. I'm sure that isn't surprising to anyone, it was a long shot. So now I'll be shooting for the fall get together in Townsend. We will see.

BWA

Scott it is looking good!!
On my TR6 I used the stock TR6 temp sender and mounted it into the aluminum thermostat housing on the 3400.
My buddy that did the electrical work told me that it would have to be properly grounded.  I told him is it not grounded to the engine via the aluminum housing.  He replied that it is better to have a separate ground to the sender than have it ground through the aluminum body.  So I made a washer with a tag on it out of copper and it is held in place by the sender.  The ground wire then plugs onto the tag.

Cheers
Byron

Scott Costanzo

QuoteOn my TR6 I used the stock TR6 temp sender and mounted it into the aluminum thermostat housing on the 3400.
My buddy that did the electrical work told me that it would have to be properly grounded. I told him is it not grounded to the engine via the aluminum housing. He replied that it is better to have a separate ground to the sender than have it ground through the aluminum body. So I made a washer with a tag on it out of copper and it is held in place by the sender. The ground wire then plugs onto the tag.

Thanks for the feedback Byron. Interesting. I ran the same sender on the aluminum lower intake on my V6 and it seemed to work without issue. Was your buddy worried about gauge accuracy? Is there that much of a difference between an iron block and an aluminum block? Just curious.

mgb260

Scott, I've heard of Teflon thread tape causing issues with grounding sending units. Hey, you're getting there!

BWA

Scott I talked to my electrical buddy and he has 2 reasons:
1/ On the 3400 all sensors that attached to aluminum bodies came from GM with both a power lead and a ground lead.
2/ With dis-similar metals you get corrosion issues, oxides that build up and create resistance.  Aluminum is bad for this.

On your fuel lines will you have to go to  larger lines for the bigger thirsty er er er engine?

Cheers
Byron