Ken Hiebert's 1965 Jaguar E-Type with GM LS1 V8, "Part 10"

Started by TR6-6SPD, November 16, 2026, 09:26:09 AM

Previous topic - Next topic

TR6-6SPD

Here is a link to "Part 1" of the project:
https://www.britishv8.org/smf20/index.php/topic,36697.0.html

Here is a link to "Part 2" of the project:
https://www.britishv8.org/smf20/index.php/topic,37548.0.html

Here is a link to "Part 3" of the project:
https://www.britishv8.org/smf20/index.php/topic,38597.0.html

Here is a link to "Part 4" of the project:
https://www.britishv8.org/smf20/index.php/topic,43345.0.html

Here is a link to "Part 5" of the project:
https://www.britishv8.org/smf20/index.php/topic,50240.0.html

Here is a link to "Part 6" of the project:
https://www.britishv8.org/smf20/index.php/topic,61699.0.html

Here is a link to "Part 7" of the project:
https://www.britishv8.org/smf20/index.php/topic,64654.0.html

Here is a link to "Part 8" of the project:
https://www.britishv8.org/smf20/index.php/topic,68003.0.html

Here is a link to "Part 9" of the project:
https://www.britishv8.org/smf20/index.php/topic,72269.0.html

Windshield Install

Whether or not the windshield I purchased many, many years ago would fit was a major concern for me. After reading on the Jag-lovers forum, how other people experienced difficulties installing their new glass because it was shaped improperly, I was prepared to encounter the same. Apparently the wooden mold in which they drape the hot glass over to achieve the correct shape was mishandled, was damaged and a string of defective windshields were sold. It seems I had one of these. I read stories of people returning multiple windshields until they lucked out and found a correct one.

The shop I bought mine from is now long gone and shipping from Canada would be prohibitively expensive anyway.

The problem comes from the bottom corners being too wide for the body opening, something the rubber seal cannot compensate for, this being about 3/8" per side.

To confirm all of this, I set the glass in place just before I sent the body out for paint. What you want is for the glass and the body pinch weld to line up and retain about 3/8" to ½" gap all the way around.

My fix for this was to modify the body to match the glass.

At the two bottom corners, I pie cut the metal and bent it out to match the glass, then filled those gaps. At the top corners I had to add metal to close the space.

Glass set in place:
IMG_1485.jpg

Corner pie cut to adjust width:
IMG_1480.jpg

Proper gap at top:
IMG_1483.jpg

On my first attempt to install the glass on the painted car, I failed. Things were too tight in the corners. I pulled the glass out, masked off the car and ground off up to 1/16" of metal in areas to give more space.

On my second try, I put the rubber seal on the body, then put the glass into the seal on the bottom edge, then worked the seal around the glass from the inside out.

I used soapy water, nylon probes, no silicone, no rope.

Rubber on body:
IMG_4866.jpg

The final top corner was the hardest, of course. Next was to apply a windshield sealant to the body and glass side, then install the locking strip.

After that, I installed the chrome trim, upper and lower, then the two side "hockey sticks".
The rain gutter trim finished the job.

A great relief to see it done:
IMG_4921.jpg

Thanks for looking.
Ken