Miata 1.6 into a 78 Spitfire

Started by mildo04, March 26, 2012, 09:19:40 PM

Previous topic - Next topic

mildo04

Winston-I did get the triumph gauges working....well, all except the speedo, though I have a plan for that for the next time I take the trans cover off.   I'll find my wiring diags for the tach and water-they were pretty simple.  I know the water gauge was as simple as plugging it into the sensor at the rear of the intake on the 1.6 engine.   The problem is though-the miata runs a bit hotter than a spit engine by design so the gauge was dam near at max before the fan would kick in.  It was giving me a heart attack so I bought a new gauge from Vicky brit that had real numbers on it up to 250.  It came with a new sensor which you do need to use.....that is the biggest pain, getting the old one out and putting in the new.

Fuel gauge- no change
Tach-I'll post tomorrow
Speedo- the jury is out for now

I am thinking of adding an oil pressure gauge since the engine has the sensor there...

Doug

Winston

Thanks in advance, Doug. Wiring is not my strong suit, though this project is forcing me to learn :)  I'm interested to hear what you have in mind for the speedo. That certainly seemed to be the most difficult to adapt.

I support adding an oil pressure gauge. Most important gauge you can have, in my opinion -- but that's racer mentality for you.

mildo04

for wiring in the ECU and trimming the miata harness..you definitely will need some strong wiring diagram "interpretation" skills...here is a link that i used-printed out and made notes on the margins as i went along tracing circuits....it is a grungy, greasy mess now, but was invaluable.  

http://www.madracki.com/miata/images/wiring/90diag.pdf

i believe there is similar ones for other years...as i found-the haynes manual has alot of mistakes in it.

The Miata Garage had some similar, great information, pictures and diagrams:

http://www.miata.net/garage/

doug

mildo04

Tach Wiring...it is really simple-hard part is routing the wires and splicing into or replacing the original spit ones (and of course getting at the back of the tach)

excuse the drawing-i am not a CAD person.....
Tach Wiring.jpg

Winston

Great information, Doug. Thanks a bunch!

The madracki.com diagrams are great. That's what I am using for my swap. For others that may be interested in a Miata swap, here is a direct link to the various diagrams from 1990-2000:

http://www.madracki.com/miata/wiring.html

avdodger


Moderator

taken down by owner, I expect...

but you can find some of that old content archived here:
https://web.archive.org/web/20111025095811/http://www.madracki.com/miata/index.html
1971 MGB GT V8
Buick 215 w/ Rover heads, custom EFI & crank-fired ignition.
Custom front and rear coilover suspensions.

Winston

Looks like the Turbo Miata guys (or somebody they know) saved the Madracki site's Miata stuff, including the diagrams:

http://y8spec.com/wiring/

nutos

Hey Nice lookin conversion. Im doin the same thing at the moment. I managed to get the motor behind the rack and as low as possible while keeping the shifter about the same.
Did you manage to marry the spitfire speedo to the mx5 box?
Would love to ask a whole other bunch of questions too if that's cool. The most important is "Does it go extreeeeemly quick??"
As that's what Im hoping.
Cheers.

mildo04

Aiden,
let me dig into my notes...i had written up how i hooked up the speedo-it was an adaption of parts from both cables...a bit of a pain in the butt.

does it go fast......   you'll see.....i still get a rush when the miata power really kicks in above 3k....it is like a turbo rush...
i haven't tryed a "top speed" test as the front end get a bit light(even with the front end lowered) above 90....but i would  estimate it could do 120+ if i got it on a  track....

feel free to PM me with any other questions....i have it in the garage for the winter and am planning some additional work on it...

pucksaq20

Wondering real quick about this, did you use the original harness with the ecu mated in or an adapted miata harness.

mildo04

I used both....the original spitfire wiring for lights, horn, radio, etc.  the Miata harness  for engine, fuel, cooling, charging.batt.  You do have to  morph.connect them for ignition key and to power the spit harness.  I put the ecu in the passenger footwell, the fuse box and relays in the original battery box.  I relocated the batt to the trunk.  

The wiring was the most difficult part of the conversion.....

rbrown0891

Doug,

I am at the start of the same swap.  Was curious if you had any closer pictures of your motor mounts/steering shaft clearance with the exhaust manifolds?  Seems as if I have a pretty good conflict with the steering shaft right at the flange.

Any help would be appreciated.

mildo04

i'll post some better pics this weekend and some measurements in relation to some common frame items for you.  I had a rough idea of the location and shape of the mounts based on the article in the magazine, then used stiff cardboard templates to get the location and angles right before I fabricated the mounts to weld on....I necessitated many trial fits and banged knuckles before I was confident to weld in the brackets....and some fun maneuvering of the engine on the final lowering onto the mounts-but it was well worth it.  the clearances are DAMN tight with the manifold and steering shaft.....

d

mildo04

Also-I believe I did do some grinding of that portion of the flange just to give a small amount of extra room....I didn't have to take off too much or have an impact on the integrity of the flange joint itself.

joebarry10

Hi.  New to the forum, so sorry for the late post.  I have started assembling the parts needed for ,y own Miata engine swap for my 79 Spitfire.  I have an pretty good idea of what parts I will need, but my main absence of knowledge is in the wiring.  Could you guys please tell me what wiring needs I will need to get my project running.  I have the ECU and all bits of wiring from the behind the dash and engine compartment - but I know I dont need ALL of it.  ANY help will be much appreciated.  Will add photos after I have all the pieces gathered and ready to go.  Thanks.

dbeliveau

Doug,
Any more pics of your Spitfire?
Dan
80Spit after7r1 (1024 x 768).jpg

rbrown0891

Barry,

I started with the complete Miata wiring harness and took off what was not necessary (much more tossed aside than used).

I had a couple questions about motor mounts - here is what I did.  Note that I think the engine is still just a bit high 1/4-1/2".  I am going to try to notch the oem mounts where they mount to the engine to drop it a bit.  Note also that my car had some frame rail issues that were fixed that could have inhibited getting the motor down further.  I also thought I read that the angle of the mazda mounts are 60 degrees, but I measure them at around 55 degrees.

Ryan
motor mount2.jpg

DiDueColpi

I would try to modify the frame brackets first Ryan.
The reason for that is that it's a PITA to modify the mount every time that you have to change it.
Not a big deal, but, the more stock parts that you can retain. The happier you'll be down the road.
(Imagine changing a mount in the motel 6 parking lot of, "I just want to get outta here" Alabama)  

Live like you mean it.
Fred

mildo04

Sorry for the delay-work interferes with the important stuff.  I agree with Ryan-start with a Miata harness and remove what you don't need....I would say about 1/2 the harness is not needed(AC, lights, horn, etc)...use the existing spit wiring for all the other stuff except engine management....you will need to merge the 2 in a few places-fuse box, ignition, alternator-but it is pretty straightforward(but time consuming).  I am attaching pics that show the locations of the mounts.

mine are very similar to what Ryan has...you can see by the pics the location on the frame on both sides....essentially right in line with the lower suspension pivot/mount.  the clearance on the driver side between the mount and the steering column and the exhaust flange are TIGHT..i did grind down the flange some to ease my mind.....at some point I may try to fabricate a new exhaust system and move the flange further down...but that is for a future burst of energy....

mildo04

photos to follow as soon as I can shrink the files in size...



mildo04

the last 2 pics are of the passenger mount...sorry the quality isn't better...but you get the idea of the location as well as how tight it is on the driver side.

Mañana

Hey Doug, glad to see this thread active again.

For the other guys, I got my swap done this past spring, took 3 months, but lots to do to pretty it up.

Finally got enough stuff together to put up a website...
This takes you right to the technical stuff, bypassing all the chaff.....
http://stevew10.wix.com/spit16#!blank/d4a4m

Still tonnes of details and info to share and I'll get back at it in March.

Hope it helps.

Steve

PS: Dan Patrick's article is there as well (you can get it through the Links page)