Clutch master question

Started by rficalora, February 13, 2010, 11:41:32 PM

Previous topic - Next topic

rficalora

Ok I switched to an early pedal box.  Got an early dual circuit brake master (the one with the round resovoir that's sort of slanted looking).  Also have a Tilton 75 for clutch master... must have missed measured because the resovior on it is hitting the brake master resovior.  Anyone know the piston size on the stock MG clutch master used on early cars -- or other clutch masters that'll fit in the early style pedal box with the stock MG brake master?

jimbb88

Rob, as far as I know, all the CLUTCH masters are the same, it was the BRAKE masters that changed. I believe the clutch master bore is 3 /4".

rficalora

Thanks Jim!  

Speaking of brake masters, anyone know which flare type the early style dual circuit (tilted round reservoir) brake master uses?

Bill Young

Bubble type flares Rob. Rob, if I'm not mistaken the remote resevoir kit should fit the type 75 cylinder and get that out of the way easier than finding another master cylinder. Of course the stock B unit would work if you have one handy as well.

rficalora

Thanks Bill -- bubble flares.  With respect to the remote reservoir for the Tilton 75 -- it can be set up that way.  The MC even came with the parts to do that.  But, I want to keep the reservior neat & over in the pedal box area & there's not much room for it there.  I'm going to play around with it to see if there's a way to mount it that'll look good.  If not, my 2nd choice will be to do some measurements on the Wilwood MC with integrated reservoir -- like this... it comes in a bunch of bore sizes so if it fits the area & I need to adjust the pedal feel I'll have more options than if I go with the MG clutch master.  Oh, & it's less expensive than either the Tilton or the MG one too.
Wilwood Clutch MC.jpg

67MGBV8

Rob,
The earliest MGB's used a clutch master cylinder with the reservoir can straight up, when the dual circuit brake master cylinder appeared the clutch master cylinder "can" was tilted toward the fender a little bit to  provide more room for the wider brake master cylinder reservoir.  Girling masters will work and are available with integral and remote reservoirs in .625, .7, and .75 inch sizes.  They have close to the correct bolt pattern as I recall.

mlieb

Ok Been out of the loop for a while but I`m ready to get back at it. (god willing)
I`m having a bit of a time with the whole clutch thing so I thought I mite go with a hydraulic throw out bearing.
My question is What should I use for a master cylinder?
I`m using a 2.8 with a t-5 tranny and the stock master cylinder just does not seen to have enough "stuff " to engage the throw out.I shortened the throw out arm,used a slave from a 1500 and everything you did Bill but I still cant get the bearing to engage enough.
Just think that this will save me a lot of trouble.
Any advice or suggestions ?

Bill Young

Hi Mike, good to hear from you again. From what I've seen and read almost all use a 3/4" bore master cylinder on the clutch with a HTOB or most British type slave cyinders. Give Brian McCollough a call and see what he recommends. I'm pretty sure the HTOB he uses will work with a stock master cylinder and from what I've been able to find out the bore on the B or Midget is the same, should work with yours.
As to your problems of not getting enough release action, that's one I can't figure out. I remember the photos you posted at one time for your mods and from what I saw it should have worked. About the only thing I can think of would be that the push rod is a bit on the short side and not giving you all the available stroke in the slave cyinder to work with.

motek

I just spoke to Tilton yesterday. I also can't disengage their hydraulic throw-out. They say I need a 7/8" bore. I ordered the Wilwood. Maybe 3/4" will work for you but I don't know.

donfaber

I used the standard Clutch Master Cylinder from my 79 B, with the HTOB I got from D&D - McLeod, I believe. T5 Camaro tranny with Chevy Clutch. After I got the HTOB correctly adjusted, no problems.

ex-tyke

I second Don's comment. When I had the Olds 215/T5 and a Mcleod HTOB from D&D, it adjusted and operated fine with the std 3/4" bore MGB MC.

MGBV8

That's what I have used since '01, stock MGB master cylinder & Mcleod HTOB.
Carl

motek

Sounds like 3/4" works on the Mcleod. My stock Triumph bore is smaller.

kstevusa

Rob, the stock cyl. worked great on my HTOB, but the effort was excessive.  I changed to the Tilton 5/8" and everything still works great,  The key is setting up the  Brg. at installation.  There is a Tool to use for this purpose. some do not use it and do the measurements manually.  Speedway Motors has this tool listed.

rficalora


kstevusa

I have the Mcleod-Weber brg. I purchased from D&D at V8 meet in 2003 in Townsend Tn.  It was just weber then, but Mcleod bought them out and is now  joint named.

Bill Young

Rob, I think that brg. is just Tennessee shorthand for bearing.

rficalora

got it.  I'm not suing a HTOB... I copied either Graham or Joe Schaefer using a Toyota truck slave.  No info came with my clutch but I've read the throw out bearing is supposed to ride on the pressure plate.  I couldn't find anything saying how much so right now I have it with "moderate" pressure -- basically the pressure exerted by the spring in the clutch slave.  Once I fix the water pump leak & get the car idling smoothly, filling/bleeding the clutch is next.

BlownMGB-V8

Rob, I guess it was common knowledge for so long that it's been lost to the world ;-) but in the case of roller type TOB's (throwout bearings) best practice is to hold the bearing just off the pressure plate fingers on release. They do wear and there's no point in encouraging them. With mechanical linkages it was easy, as the return spring would retract the TOB. (If you left the return spring off you might soon be replacing the TOB.) With external hydraulics, a return spring, judicious adjustment, and sometimes a stop was used. With HTOB's the manufacturers rely on such esoteric forces as seal memory and the irregularities of the pressure plate fingers to establish a running clearance much like with a disc brake. It seems to work but probably as much because of improved quality in the bearings as anything. Carbon TOB's as originally installed in the MGB are a different animal and are apparently designed to run with slight pressure against the mating flange.

JB

ex-tyke

If Rob is using a std Ford TOB (as used typically in a Fox body Mustang, eg), these are a "constant motion" type and are designed to be in direct contact with the clutch diaphragm fingers....in other words, the TOB has a slight preload on the fingers and is in constant rotation.
I found reference once, that the engagement force was something on the order of 4 lb.

rficalora

Graham is right, the TOB I'm using is a standard Ford as used with mustangs.  I have whatever force is applied by the spring inside the slave -- I'm guessing it's more than 4lbs but wasn't "hard" to push the slave into position.  Graham how did you adjust to get a good "preload" --- is it a matter of finding an appropriate spring to pull the fok back -- e.g. a spring from the fork to the bell housing that counter-acts some of the slave force?

ex-tyke

Rob, the preload is obtained by lengthening the slave cylinder pushrod (adjustable) and thereby forcing the TOB forward into the diaphragm - 4 lbs isn't much and it's a bit of a guessing game. You shouldn't need a return spring - the clutch diaphragm is the basic return spring.
....hmmmmm, unless you opted for a pull type slave in which case you maybe left to spring pressure.......have you got a photo of your installation?

BlownMGB-V8

Also be aware that as the clutch disc wears the fingers of the pressure plate will move towards the TOB. Your slave has to account for this, otherwise you have to make periodic adjustments. Otherwise the clutch will start to slip as it wears. I always liked having a bit of play before the bearing touched the fingers. It allowed me to gage how fast the clutch was wearing by the decrease in the pedal free play.

JB

rficalora

I haven't taken a picture of mine, but it's a push slave just like Joe Schafer's.  It's also mounted similarly -- except I made the bracket that holds mine so the bleeder is at the top.  It is mounted close to the bell housing & with the push rod going through it like his.  

JoeSchafer-clutch slave.jpg

When I installed mine, the slave was about 2" away from the bell housing when the push rod started pushing on the fork.  As I pushed the slave into position, the push rod pushed the piston in the slave back.  Not sure if there is, but it felt like there was a spring between the slave piston & the back of the slave... it's that force that's holding the TOB against the fingers on the pressure plate.

It's hard to explain but did that make sense?  Thoughts on that set-up?

ex-tyke

I'll see if I can walk you through your clutch installation setup (assuming the system has been bled and all components in place.:
1) The first thing I'd do is to adjust your clutch pedal free play to about 1" by adjusting the pedal fork rod actuating the Master Cylinder. Pedal should travel 1" before the MC piston starts it's movement.
2) Manually push the clutch release fork as far forward so that the release bearing is just contacting the clutch fingers. Adjust the length of the slave cylinder pushrod to hold the fork at this position - now lengthen the slave pushrod slightly to achieve your 4 lb preload for the fingers.
With the Ford constant motion release bearing design, I don't see that you need a separate fork retraction spring - the clutch fingers will retract the fork/bearing and the slave cylinder piston (which also has benefit of a piston spring.)

EDIT: I have to (sheepishly) make a correction to this post, point 1) - astute MGB owners know that, while the brake MC pushrod is adjustable, the clutch MC pushrod is not - all the freeplay comes as a result of loose component tolerances. I blame my years working on HD trucks which have need for the afformentioned clutch pedal freeplay faux pas. Sorry Rob, et al.