BritishV8 Forum

General Category => MG Sports Cars => Topic started by: perrymgbv8 on April 11, 2015, 06:16:43 PM

Title: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 11, 2015, 06:16:43 PM
Hi guys !
I have decided to get rid of the Rover V8. The engine has done really well for me, but I need more power now. The last mistake with running the new tune without wheelie bars caused me to spin two bearing shells due to the angle of the car off the line. I was very upset about the damage but it was my fault as I should have had the wheelie bars fitted. So I have decided to rebuild the Rover with a new offset ground crank and new chevy rods which will be modified to my old specs. I want to sell the engine and I wont bodge it up to make it work by using the scuffed crank and two scuffed rods. So its all new parts and a fresh build so I can sell the engine in "as new" condition as a complete unit including the 4/71 and induction system.

Hopefully the new owner will have fun with it.

I now have a 4 bolt small block chevy engine as the core for the new build for the MGB.
All of the internals will be removed and the block will be checked for line bore and straightness etc.
Then it will be cleaned and honed so i know what my final bore size will be.

I have already bought some of the new parts for the engine which include:

A pair of Brodix 225 cc dragon slayer heads.
MSD digital 7 ign system.
MSD billet dissy.
Comp cams noisy cam gear drive.
Edelbrock dual quad tunnel ram inlet manifold.
Two 600 dp Holley carbs.
A set of comp cams Pro Magnum stainless steel roller rockers.
Comp cams 12-773-8 mech roller camshaft.
Comp cams mech roller lifters.
Enderle twin carb linkage kit.
Hedman Husler Zoomies.
A pair of vintage MT ally valve covers.

I will buy a full forged and balanced rotating assembly when I know what the final bore size will be as I am looking for a CR around 12:1 or as close as I can get to it.

The list of small parts is going to be quite large as I need stuff like starter motor, electric water pump, sump pan, alternator, front timing cover, plug leads, shotgun scoop for dual quad setup, gaskets all round, a custom made radiator, radiator fans, push rods, ARP stuff all round, and minor stuff like valve cover bolts, plug lead separators, crank trigger wheel, crank sensor  etc etc.....  The list will no doubt grow :)

My intention is to build a base engine that will produce 700hp on the carbs alone. But with internals that will cope with around 1000hp as I may want to run nitrous in the future ?

I want this to be my last engine build for the MGB. And I want it to be able to run back in the mid 9's on the strip without being stressed. And I then want it to run the MGB into the 8's with a little nitrous or race fuel and more timing ?  

I have to admit that I have enjoyed the years of learning how to the get the Rover V8 to make good power. And I am now doing it all over again with the SBC. The main difference being that the Rover is expensive on parts to make good power. But the SBC has been used in the USA for many years and from what I can see all of the research has already been done. I just need to ask the right questions to the suppliers of parts and I can get what I need to build the new engine I want ;)

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on April 11, 2015, 09:05:10 PM
Hey, Perry! How's the rear axle holding up? Lots of proven parts for the SBC. I see some 8 second times in your future!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: theonlyiceman53 on April 11, 2015, 09:11:09 PM
Sorry to see you leaving the Rover behind but glad that you are going the SBC route.  Hard to beat the power to Dollar ratio of a SBC.
Cheers,
Bill
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: Jim Stabe on April 11, 2015, 09:37:31 PM
What kind of power were you getting from the Rover? You should have a lot of fun with the Chevy and more worry free.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 14, 2015, 06:22:16 PM
Hi guys!

The rear end is holding up just fine so far.

The old Rover made 525 on the dyno for its last run on the safe tune before  I fitted the zoomies. This was with timing knocked back by 10 degree's from where it should have been. When i fitted the zoomies my dyno guy did not want to run the car on the rollers as he did not want the dyno room to be filled with fumes. since then I added 8 degree's of timing and another 25 shot of gas. So i'm guessing the engine ended up making around 580hp ?

The $ / £ ratio of buck to bang with the SBC is now the main factor for the MGB. I am going to build the SBC for half the cost of what the MGB is putting out now I think :)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on April 15, 2015, 07:24:23 AM
The SBC is a known winning combination that you can hardly go wrong with. While just shy of 600 HP with a Rover is quite an accomplishment the Chevy will be more reliable at those power levels, and as you say, cheaper. Too bad about the extra weight, but with enough horsepower who cares, right?

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 25, 2015, 04:33:41 PM
Thats my train of thought Guys !

I still feel a little sting about retiring the Rover V8 as it came from the factory with one fitted. But I'm 57 this year and I'm tired of developing the Rover engine now on a limited budget.  Despite my inbred British loyalty to the MGB and the Rover engiine its time to do the sensible thing and fit  better motor for what I need the car to do now. I have set aside £1000.00 to get the old engine back as new. Then I will sell it for £6,000 if I'm lucky. That will still see me £6,000 in the hole, but it will mean I have that money to finish the SBC by the end of this year.

And hopefully the SBC will pull me into the 9's as a baseline on the carbs once its been shook down, :)

September is when I hope to be driving the MGB again and if i get enough track time I can tune it ready for the 2016 season ?

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on July 22, 2015, 03:08:44 PM
I now have a buyer on the hook for the long engine only for £3300.00 so that means when i sell the whole blower and inlet setup I should almost hit my £6000 goal. :)

Sadly work and family / home stuff are sucking up my spare time. But I still hope to have the new engine built and ready to drop in by Christmas time. So realistically I want to see the car back on track around April 2016 ;)

More parts are arriving. I now have a very nice Moroso Electric water pump :)

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: billymgb1000 on July 22, 2015, 06:37:03 PM
Hello Perry I hope the sbc does it for you, they are proven no doubt. If you didn't already have that motor I would say LS1 that motor is incredible 5.7 or the 6.0 and now the 6.2 just think 6 bolt mains and aluminum heads from factory the ls1 tech.com site is full of guys drag racing these motors and now they are putting turbos. and makind 1000hp anyways good luck and keep us updated
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on July 23, 2015, 10:10:21 AM
Bill's right about the LS engines, they have simply taken over. There have been a few swapped into MGBs also. Scott had his LS4 conversion at the meet last week, very nicely done. Several engines in the series could be suitable, all with the same basic size package. It is definitely worth looking at.

You could look at the older SBC as a stepping stone, but much has changed between the two, so it could make more sense to go with one of the less expensive LS versions and upgrade that later.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on July 23, 2015, 10:54:07 AM
We need to rethink this engine. Perry, how in the world did you decide on a 383 long stroke torque motor for that lightweight MGB?

If it's 383 vs 377, I would take the shorter stroke 377 every time. Of course, you need a 400 block & 350 crank.

For a dedicated drag car, too much torque off the line is not a good thing. A better breathing high revving engine is, IMO. More fun to run 'em down & pass 'em on the big end of the track anyway.  :)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on July 23, 2015, 12:41:30 PM
Perry, I agree with Carl in theory but for inexpensive build the 4" bore is best. The 383 low end torque will be moderated with a cam one size bigger in duration than you think you need. Install straight up and move the power curve up.  Make sure and do the 6" long rod version with shorter lighter piston. Your next upgrade may be a Powerglide. Keep us posted.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on July 23, 2015, 05:27:32 PM
The 377 uses a 0.030" overbore 400 for a 4.128 bore that unshrouds the bore even more. The 383 will be externally balanced & not near as smooth as the 377.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on July 23, 2015, 05:58:17 PM
Scat sells a reasonably priced internally balanced crank + 6" rods for the 383. Ebay has a deal on Howard's Forged pistons for that combo also at $450. My brother raced a SBC 400 Pro Gas/Bracket Vega. Body was just a shell with Lexan windows and roll cage. He used block filler, head studs and expensive custom forged pistons. Victor intake with 850 Holley double pumper. He used a Comp cams grind also. It was a screamer and made it to low 9 ET's.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: pcmenten on July 23, 2015, 07:20:25 PM
Funny. I would have started with a 400 4-bolt block and either offset grind the stock crank (417 ci) to use 327 rods, or picked up an aftermarket crank (427+ ci). That's as big as the larger LS engines. No replacement for displacement. Heads are plentiful and cheap. Roller cam conversion is also simple.

I built a 400 for a 55 Chevy but sold them both (together) before the project got done.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on July 26, 2015, 09:08:50 AM
Perry, Here is a good article on building the 383:

http://www.hotrod.com/how-to/engine/ccrp-0808-383-stroker-small-block-chevy/
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on July 28, 2015, 05:36:04 PM
Thanks for the feedback chaps! I'll be doing some reading :)

I think most of the reading will be done in the next 3 weeks while I'm off work for my summer holidays ;)

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on September 15, 2015, 07:35:26 PM
Perry, Anything new? How did the mounts work out?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on October 24, 2015, 07:35:00 PM
Hi guys!
The mount frame looks like it will be ok.The SBC is still just a heap of boxes and loose parts right now.

I'm just spending some time rebuilding the Rover to as new spec for the new customer who will be handing over £6k ($9,200.00) in cash in a few weeks,

I have to say that I am more than happy that my old engine will be going inbto another MGB. This is Phil Herricks old SuperBee. The SuperBee is at least 500lbs lighter than my GT and it just ran a new PB of 12.2 with its 360hp Rover V8 fitted. I think my Rover V8 with the blower and nitrous with the extra 220hp will push it hard onto the low 9's

I am still deciding on my final choice for the rotating assembly. But it will be all forged components that will be internally balanced. I'm thinking 12.0:1 CR for use on pump gas so I can squeeze all I can from the engine just on the carbs while still leaving some room for the additon of nitrous.  Another change for later will be to remove the TH350 and fit a Glide. But for 2016 I will have to keep the TH350.
I may have to alter the rear end ratio for the SBC engine as it will rev and pull much higher than the old Rover did. I cant afford to mess with the 3.07:1 MGB axle which I fitted Ford 9" internals to, so I may end up fitting smaller slicks instead ?  

Whatever happens with the build I will just test and log data as I normally do until it runs an 8 :)

I'm not bothered about the additional weight of the SBC because I'm not fitting the blower assembly on this engine. I think the fiinal engine weight will be very close to what i have now with the blown Rover setup ?

I am also in the thought process re making this a Methanol engine ?

I have lots of things to think about over he next few months. Pump gas? Race Fuel? Methanol?

When i make a decision i can then select the last parts I need for rhe new build..

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on October 25, 2015, 12:06:57 PM
What did your Rover with the blower weight Perry? If you run aluminum heads and intake on the SBC you could be close. The potential for NA HP is very high of course.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on October 25, 2015, 04:16:23 PM
Perry, Some drag cars stateside like E85. 85% Ethanol/15%Petrol. Less corrosive than Methanol. Cheap, as it is used in Flex fuel cars and available at gas pumps.You would need almost twice as big of jets and steel needles and seats. Also any rubber lines rated for Ethanol.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on October 31, 2015, 07:30:57 PM
Hi Jim
The SBC with the ally Brodix heads will possibly be lighter than the blown  Rover engine. Or at least the same weight I think.

Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on October 31, 2015, 07:32:16 PM
Jim N

Thanks for the info :)

Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 12, 2015, 10:49:36 AM
Perry, I look forward to your build. I am getting ready to build an engine for a vintage nascar I have. I am going to intentionally keep it to 350 just to keep in line with how the cars were raced. I plan to start buying parts at the begining of the year. This is the block I will likelly start with:

https://chevroletperformanceparts.com/p/24502503-350-cast-iron-bowtie-race-block
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on December 12, 2015, 11:32:31 AM
358 ci. ;)  Here's your engine, Gary.  :)

http://www.hotrod.com/how-to/engine/hrdp-0803-chevy-nascar-engine/
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 12, 2015, 03:51:57 PM
That is neat, but probably a little more advanced then I want to go on a 1990 Nascar. It won't be a 100% erra but mostly so.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on December 15, 2015, 10:39:13 AM
What paint scheme?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 15, 2015, 12:16:20 PM
This one:

(http://api.ning.com/files/oxFTMOUoPq0EfT3iYS7jf*OuXx680FLORcMGniXghyiO1-JVXRT*h8MU110uLY7sUz31DekHCZgioUwRo*GPU4Lr78CSPpE1/457.jpg?transform=rotate%2890%29&width=737&height=418)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on December 16, 2015, 11:41:39 AM
Great choice, the Iron Man. He used to destroy Late Model Sportsman right here in Kingsport, TN back in the early 70s. One of the best short track racers ever, if not the best. His home is only about an hour & 15 minutes from here over in Asheville, NC.

Of course, if I were doing what you are, Gary, I would have to back up 3-4 years to honor one of the most wide open, hardest charging drivers.

(http://i118.photobucket.com/albums/o96/toomuchcountry/Tim%20Richmond/TimRichmond86a.jpg)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 16, 2015, 12:43:42 PM
only problem is this is one of Jack's cars that he raced which is also a Banjo Mathews Chasis.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 16, 2015, 12:46:42 PM
BTW this will be a full ground up build. I took the body panels off, and it is at the sand blasters right now:


(http://www.rc-tech.net/cars2/NC/NCStripped.jpg)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on December 17, 2015, 05:13:12 PM
How did you wind up with one of Jack Ingram's cars?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on December 17, 2015, 07:57:25 PM
Auborn Auction
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on January 30, 2016, 05:40:23 PM
The new SBC engine for the MGB has now taken a turn in the overall plan for the build ??

I have just ordered a new Dart SHP engine block for the build. There were several factors that lead me to this decision. But I think this is the next best course of action for me now. My old 4 bolt block was overbored to +60 thou and I'm not happy that this old block will stand up to the abuse I intend to give it ? Eventually it will be supercharged, but until I can afford a new blower it will have to put up with a lot of Nitrous abuse.

I took some time to look at the list of parts I have collected in the last 18 months and saw that everything was brand new apart from 50 year old engine block. The carbs will be the only things that are not brand new for this build now. And if I can find some money in the next 6 months they may also get replaced with new tuned and matched items? The new Dart block can be bored to give me a nice 430ci motor while still having bore walls 1/4" thick?

The MGB has been off track for 17 months now so I guess another 4-6 months isnt going to kill me eh ?
I just want this to be my last engine build, but also my first ever NEW engine build :)

When the new block arrives I will make a final decision on the crank + rods + pistons so i can finish the buuld.  When the new block arrives in 2 weeks i will also need to have it fitted with cam bearings as well as making a decision on the final bore size and deck height.

I'm hoping that by mid to late April I can start bolting stuff together :)

Regrds to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on January 30, 2016, 06:13:43 PM
Perry, Thanks for keeping us updated! I'm curious as to how the Speedway mounts will work out in the MGB.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on January 30, 2016, 06:39:27 PM
Wondering what displacement/bore/stroke you are thinking towards? Redline? Lots of potential there.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: burner1 on February 01, 2016, 09:53:35 AM
That stuff takes time. I am trying to source all the parts for mine. Spent a lot of time measuring and researching.


(http://www.rc-tech.net/cars2/NC/NCEngine/NCEngine1.jpeg)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 23, 2016, 09:05:59 PM
Hi Jim!
I'm going for a tame 383 build on this new engine.
The new block is capable of running much more CI but I dont think i will need it?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on April 24, 2016, 09:18:45 AM
Carl thinks using the 400 block with the 350 crank would be a better drag engine, (room for bigger valves and lower piston speed.)

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on May 03, 2016, 07:52:33 PM
AND, the shorter stroke. We already have traction issues (maybe not Perry), so I tend to prefer short stroke, free revving engines that move the power farther up the range.  I can't use 300 lb-ft of torque at 1000rpm.

Well, now that Perry has purchased an aftermarket block, he can build anything he wants all the way up to a 440 cubic inch small block!


The 377 vs 383 dilemma.

Quote377
Pros: Large bore, short stroke engines are always slightly better at making top end power. A typical NASCAR engine is based on the same design although they don't use production engines.
Cons: Finding a 400 block. Main bearing spacers for the crank are not cheap.

383:
Pros: Available from just about everyone. Aftermarket stroker cranks are cheap so you don't need to find an old 400 cast crank. Plenty of kits available to make it in a 1 or 2 piece rear main block. Makes more torque than a 350.
Cons: If you're going to use a crank out of a 400 to make a 383, just build the 400.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: DiDueColpi on May 03, 2016, 11:14:33 PM
Totally agree with you Carl.
 My old Volvo ran a 377 sbc. Pulled off an 11.82 @ 127mph and drove it to work every day for years.
These days no need for spacers or line honed 400 bearing sets. Scat and a few others make a 3.50" stroke crank in the 400 main journal size.
Makes a very nice engine. Really  free reving, great breathing and for us traction challenged individuals, a bit of a torque break down low.
And like you said Carl if you're going to use a 400 crank, build a 400 and enjoy the extra cubes and bore size.

Live like you mean it
Fred
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on May 06, 2016, 05:03:38 PM
The block will be ready next tuesday as will the new rotating assembly.

Exciting times ahead guys !!

I'm still slowly saving and buying parts though. This weeks purchases were an MSD 6.25inch trigger wheel kit for the Digital 7 controller. I did scout around and even found a European supplier of MSD stuff but they were out of stock of the kit @ $389.00. This seemed to be the general price when i searched suppliers on Sunday. Then i tried the MSD website and it was on sale reduced to $291.00 so I ordered it via Ebays Global shipping programme. Postage and duty came in at around $115.00 so $406 or $280.00 ish?

And I swapped a set of new Comp Cams solid roller lifters (which are no good to me as I need 300thou taller ones for the Dart) + a little metal fabrication for a brand new in box 6.25inch crank damper. Its SFI spec and made by Fluidampr. They are around $315 in the USA but by the time its landed here in the UK with all duty paid it cost £336 delivered / $490.00 ish. This is less than the lifters cost me :)

The rule of thumb here in the UK is "whatever the $ price is will convert to £ or a little more once you have it in your hands" And that rule of thumb does seem pretty accurate :)

Thats just over £600 / $900 ish for those two small items?

I really must make a list of these prices so I can reply to those UK racers who have often slated my old Rover V8 and said the usual words of  "Mate, you need to scrap that Rover and buy yourself a 350 small block, they are cheap as chips and will give you much more power" Yada Yada.. !

Obviously these guys have never actually built a 350 race engine. I think most of these guys have old cutout engines that they have freshened up for their street cruisers ?

With regards to the 300 thou taller comp cams lifters I just went to my UK supplier and the price is £546.00 or approx $792.00  ?? I will now start shopping in the USA to see if I can get a better deal.

The build is taking its time and I'm in no hurry now as I have decided to put the roll out back to May 2017 as there is so much to do besides building the new engine.

But I am pretty sure that when the car does roll out it will be very close to the mid 9's just on the carbs. Then I can start adding nitrous. OR! by the time its ready I may be able to afford a blower?

I have been off track in my car since Sept 2014 so another year wont hurt eh?

I have taken tomorrow (Saturday) off work to crew for a mate with his big block Ford Capri. Its run down to mid 8's on the carb only. Tomorrow we will be setting up the nitrous ;)

https://www.youtube.com/watch?v=zIGrTsVIVKs
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on May 06, 2016, 11:27:09 PM
Perry, you are just having altogether too much fun.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on May 08, 2016, 04:05:11 PM
Jim said!
"Perry, you are just having altogether too much fun"

Thats the real truth Jim :)

Sadly I forgot my camera BUT!! The Capri rolled out for its 2016 Debut and the first pass was an 8.0 PB...
Then we backed up that 8.0 PB with a 7.7 second pass just to show off :)

The data logs showed the rear suspension loading up steadily from launch and not slipping back. The data log also showed engine rpm vs axle rpm to be very stable indicating no wheelspin.
The track was good and the car was pretty much dead hooking the slicks. The wheelie bars didnt have to work very hard either.

The downside is that we spent a good deal of time installing and testing the new Nitrous system which we didnt use. The chassis is only tagged to 7.5 and its run close to that on the carb only. So the Nitrous system may only come into play on bad days when we may need a little push around the 1000 foot mark?

Sorry for the low res vid :(

This may or maynot work


https://www.facebook.com/cjaques1/videos/10154848097363135/
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on June 24, 2016, 03:05:13 PM
UPDATE!!

I should be able to buy my new lifters next week :)

Not sure if I mentioned this before but, I have decided to have the engine bedded in and then tuned on an engine dyno. I found a tuner who was recommended by both my engine guys and he has a good reputation. I have spoken to him about how build he wants the engine. He said to "build the engine from oil pan to carbs, fit a water pump if you want to"  Thats it !!  He said I could fit my dissy and trigger wheel and he will hook it up to his MSD on the dyno. He has headers that will fit my Brodix heads. He said he would mount the engine and check it over. Then do a bedding in session. He will do oil and filter change and then get to tuning. He said its a days work and will cost £400 + fuel and oil etc + tax :)  I will set the carbs up as best I can based on an estimate of the engines expected VE etc and he will re jet as required during the day!!

That will save me days of track testing and reading data logs etc while taking it easy.  I think this will be well worth the effort and cost ;)

I look forward to dropping and engine in thats already tuned to the max !!

I'm off work this weekend so I will try to get some pictures of thr block so far.

Regards to all
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 02, 2016, 06:30:03 PM
Update !

Not much to tell so far guys. I'm off on holiday for 2 weeks in 12 hours time. A Friend of mine is going to assemble my engine while I'm away. So I'm hoping to come back to find that the block and heads are all together with everything bar the push rods?

So i can get busy when i get back to get the warter pump and oil pan fitted ready for the engine dyno next month?

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 24, 2016, 06:24:42 PM
I got back from my holiday on 15th August and went back to work. After just 4 days it seemed like my 2 weeks in the Sun never happened ??

BUT!!
I have been to Mikes workshop and my new Dart SHP based engine is almost built ;)
I'm still working weekends again but all mike needs to do now is fit check springs so the piston to valve clearance can be checked. Next job is to fit the Tunnel Ram manifold and port match the manifold to the heads. Then I need to sort out the carb linkage for the twin side saddle Holley 600dp carbs. I have already fitted the linkage but its very stiff when opening the secondary throttle flaps and one of the carbs has a binding of the secondary flaps on the manifold for some reason?  Sadly I didnt have my camera with me ;(
I did get an email from Mike while I was in the Canary Islands to say that there was a clearance issue with the polished ally timing cover and my cam gear. I'm not using a chain on this build, I'm using a 4 sprocket dog drive gear set. He said that a stock steel timing cover would be best as it would be a direct fit. I emailed him back to say "just buy a stock timing cover and fit it"  His reply was... "I thought you would say that, so I bought one and fitted it already" :)

So far everything seems to be coming together ok with the new engine build. I just need to sort out this "Work / Life" balance thing. As I am working weekends so I can pay my friend to do my hobby for me? ;)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on August 24, 2016, 06:41:38 PM
Perry, Thanks for the update! Are you running open spacers under the carbs.  If you are, the throttle blades are binding in the carb base plate bores.  Do they have annular boosters (better atomization, more like TBI)? Round rings above the throttle bores with small holes.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 26, 2016, 03:12:08 PM
Hi Jim!
As yet the carbs (two 600 holley double pumpers) are sitting straight on the manifold with no spacers.
My  next job is to strip the cabs and give them a good going over. Then square jet them when i have figured out my best jetting size for the engine. I have a good selection of jets for a single carb but I will have to buy more jets. And we get stung for these over here as the jets are about $12 each. I'm hoping to go and look my engine over in the next few days to take some pics. The induction system may of course change between now and next May when i want to run the car. If i can save enough pennies I would like to fit a blower with a single or twin carbs on top. There is even a rumour that a twin turbo kit may be in the pipeline which I would love. But I fear that may set the build back another year. And I cant bear the thought of anymore time off track. The car has been dead in the water since Sept 2014 now. :( Thats will be 2 years next month !!

I'm fed up of being the wall flower at the track as all I can do is be pit bitch for the boys !!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 31, 2016, 05:42:45 PM
OK Guys!!

I wish i had a silk sheet to haul off this picture??

This is where we are at now with the new SBC / DART SHP build.

(http://i205.photobucket.com/albums/bb270/mgbv8_photo/20160831_144905_zpsv3l7zidr.jpg) (http://s205.photobucket.com/user/mgbv8_photo/media/20160831_144905_zpsv3l7zidr.jpg.html)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: kstevusa on August 31, 2016, 06:28:57 PM
Perry, "BAD TO THE BONE".  Southern slang from Tennessee :-)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on August 31, 2016, 09:21:45 PM
B-B-B Bad, Bad to the Bone.  DA DA DA DA DANT. Bad to the bone!

<iframe width="560" height="315" src="https://www.youtube.com/embed/OeGA5DLMKbQ" frameborder="0" allowfullscreen></iframe>
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: kstevusa on September 01, 2016, 07:51:24 AM
You Got It Carl!   Hell of a Ring Tone:-)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on September 01, 2016, 04:44:26 PM
Can't wait to see that one.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on September 05, 2016, 06:04:25 PM
There is still a lot of work to do!
I need to figure out an alternator and mount + a belt drive for it. I also need to save up for the vac pump system and belt drive.
These items can wait until after the engine dyno tuning next month though as the engine dyno guy can hook me up with whatever power I need to run the water pump and the MSD 7.

I was thinking about running twin race batteries and no alternator.? From what I unerstand my MSD 7 can draw 20 amps, I know my fan and pump will draw 17amps, I know my nitrous system could pull 60amps when pulsing 4 solenoids for a 500 shot.

And when I pull back into my pit I will want the pump and fan running until the engine has cooled down. So maybe 10-15 mins ?  
I have not made up my mind yet. But I am veering towards an alternator at this time )
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on November 05, 2016, 05:07:59 PM
Quick Update !

I have managed to lose one of my Holley 600DP carbs??

So in the pic above I had used an unknown spare that I bought for peanuts as a spares carb. The guy said it was working on his road car and I have no doubt that it could have been. But after stripping and dipping in the ultrasonic cleaner I discovered a crack in the main body which has been badly welded. Also one of the mounting lugs has been broken off and welded back on, and its now cracking along the weld. And when I removed the front float bowl the plastic breather was missing. And someone had blocked off the hole in the jet plate with liquid metal?  So this is still just a spare parts carb now. I'm now doing some research with Holley / Demon / AED etc about the price for a pair of matching race carbs made to suit my engine build.

My reason for looking into new carbs is that when I did the calcs for my new 383 build, the numbers showed that even at 100%ve at 7500 rpm the engine will only need 750cfm (ish). So with two 600cfm carbs the velocity through the venturi's will be lower than ideal. My worry is that the low velocity will not give me good atomisation of the fuel. I believe that modified boosters can be fitted to cope with the lower signal which will give me what I need. Eventually I will be putting the nitrous plates back on and that will lower the airflow through the venturi's as well, but I can compensate for that with extra fuel on the nitrous system as I have done in the past by using my lambda readings as a guide.

So 2 new matching carbs built to suit my engine should be the best way forward I think ?  This will set the engine dyno day back by 3 months but so what !!  The car will still be ready to move under its own steam next July as planned I think. Its been off track for 2 years now so another 8 months wont hurt. PLUS!! As I've got all new stuff from pan to scoop except the carbs it seems a little rude to not fit new carbs eh ;)

My SBC friends are convinced that one I get the engine dyno tuned and fitted it will run back in the 9's just on the carbs as they say it should make 600hp on the engine dyno. ?

Only time will tell eh :)

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: pcmenten on November 05, 2016, 09:02:30 PM
Awesome build. You are an inspiration.

I get the impression that it's not unusual to run dual Holley LIST 4150 390 CFM side-hung double-pump carbs on a dual-quad configuration. 780 total CFM.  I love the look of a dual-quad setup.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on November 06, 2016, 08:06:47 AM
Hey, Perry! Check out the Quick Fuel 450cfm. Two of them would work good.

https://www.quickfueltechnology.com/carburetors/street/hr-series/hr-series-carburetor-450cfm.html
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on November 11, 2016, 06:00:34 PM
Thanks for the comments guys!

I am now having a pair of AED 650 carbs custom built and modified for my application. The main reason for this is that AED was the only company to actually reply to my request for help.

I have been having email comms between myself and John Dickey and Jeff at AED for the last week so they could come up with a solution for my needs. In order for them to provide a solution I have had to give them all the build specs of the engine + rear gear and tyre size + a lot of other info about the engine and drivetrain + the fuel I will be using.

Long story short!!

I'm having a pair of AED carbs made to suit my exact build spec for the same price that I could buy a pair of Edelbrock 500's here in the UK ?

4 weeks and the carbs sholud be here in the UK with me so I can get them bolted on and prepare for the engine dyno :)

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on November 12, 2016, 09:24:28 AM
Glad you didn't go with the Edelbrock carbs.  They are fine for a cruiser, but I do not consider them to be a carb for a race engine.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on March 24, 2018, 12:50:05 AM
Haven't heard from Perry in a while. I asked about him on the V8Owners board also. I found this picture over there:
8354967698_f74b1a5b39.jpg
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on March 24, 2018, 09:53:15 AM
Yeah, been patiently waiting for an update on his new engine.  Hope all is well.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on May 07, 2018, 06:01:26 PM
Perry has a Facebook page. Maybe someone with Facebook could try to contact him?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on May 07, 2018, 07:34:49 PM
He posted today over on Martyn Harvey's MGB V8 Conversions Facebook page.

I told him he was missed here.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on May 09, 2018, 09:13:08 AM
Thanks for that.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on January 17, 2019, 05:14:55 PM
From Perry:

I will catch up asap Carl. New laptop, windows updates and family problems have kept me away for a while Dude! Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on January 17, 2019, 05:15:50 PM
WOW!!

My last post was in November 2016??

Sorry folks.
Please bear with the following.... It does get better !

Mum got ill and we spent most of 2017 caring for her. She lost her fight eventually and we buried her on 22nd December 2017.
Most of 2018 was a bit of a blur with trying to deal with losing Mum and sorting out her estate, and me working pretty much 7 days a week due to demand. My workload had taken its toll, and by Sept 2018 I told the boss I was taking December 2018 off work. This gave me something to look forward to I must say. Then in October 2018 Baby Bro announced that his weeks of suffering with weakness and general lack of energy that his Doctor told him was "just a virus, take these pills and rest up" turned out to be Leukemia. A.L.L type which is nasty. Baby Bro has been having treatment since then and at the moment the prognosis is GOOD!!  He is fighting. The Chemo and blood transfusion's + platelet transfusions + all the other drugs he is taking seem to be doing the trick so far. All of the family took blood tests and it turns out my wife is Haplo positive as a match for Baby Bro's Bone Marrow transplant :)  That will happen in the future when he is ready for the transplant.
I spent all of December doing DIY around the house and had 2 days on the car. I actually had my first few days of December lazing around the house and sleeping mostly. Then I woke up and fixed my heating and hot water systems in the house. Built a new Gazebo on the decking for next Summer. This was after I laid a 15ft x 15ft decking base for the gazebo. And tidied the rear garden. When I sat tidy. I mean 2 x 8 cubic yard skips full of crap :)  

I have to admit that returning to work on 2nd January 2019 was hard. I had no enthusiasm for work, but I had to get back on the horse. While I was off I had two large enquiries come in which the Boss held up until I got back God Bless him.

I have spent the last 2 weeks working furiously on getting these projects specified and ready to quote. I don't really like doing projects over £100k. But these two are working out at the moment at around £450k each. So I have to keep my game head on and get these jobs sold in the next month or so. I'm sort of happy, because if I get these jobs sold I can kick back on these jobs for 5  months and not have to manage any other works until they are complete.:)



SO!
That's all the Doom and Gloom stuff over chaps.

Now its Car Time!  

I promise to keep this part brief........

The new Dart based SBC 383 engine and the old tranny is in the car.
I had 2 days of woe with oil pressure and oil pan issues.... All sorted now.
The new engine cranks over with 45psi of oil pressure with the plugs out.
New MSD Digital 7 now fitted and working. After 12 hours of getting it fitted and working out Comms problems between MSD and Laptop.
No Zoomies made yet. Fuel system parts are now in the shop ready to fit.
So last week I fitted some hoses to the carbs and filled them with a measuring jug and a tiny funnel.
God Damn!! She fired up in no time flat.YIPPEE!!
It was only two short bursts as the cooling system isnt finished yet and she was dry.
But it ran, and it sounded nice!

This weekend I will be finishing the new fuel system. Next week I will finish the cooling system. Then I can take it on the trailer do a lonely road in the country nearby to fire it up properly so I can bed the rings in, check for leaks, check oil pressure, check fuel pressure, keep an eye on the cooling system and warm it up properly. This will be me + at least three race buddies.

That's enough for now. I will post some pics and vids asap.

Thanks for thinking of me guys!

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on January 17, 2019, 05:22:17 PM
Sorry about the low res vid folks!

It made me laugh when the guys in the VW shop next door cheered when they heard the engine start :)

Fast forward the vid to 4 mins. The rest is just waffle about the MSD and swearing to be honest.

https://www.youtube.com/watch?v=WzHo-6WDZJ0
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: Jim Stabe on January 17, 2019, 07:05:30 PM
That is a badass sounding 383
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on January 17, 2019, 07:38:57 PM
Wow.  Hope you can hold it on the strip!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on January 18, 2019, 11:37:42 PM
Perry, Glad you're back! How did the Speedway motor mounts work out for you?
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: Scott Costanzo on January 20, 2019, 07:48:54 AM
Wow, really enjoyed that video! Very, very cool project!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on January 21, 2019, 04:25:07 PM
Hi Jim!
The motor mount was perfect. I just had to shave some off the bottom to clear the steering rack. Then I added my two old steady bars from front of the engine to the inner wing and rear of the engine to the bulkhead.

The rear steady bar didn't even need adjusting. It bolted straight onto the Brodix head. The front steady bar just needed a hole enlarged in the old MGB mounting flange to bolt right on as well :)


I have spent so much time and money on this 383 build that I hope it will at least make 500+hp on pump gas. When I have tried that I intend to use race fuel and more timing to see what it can do.  

I am still trying to convince my friend Martin to let me onto his 1000hp Dyno with Zoomies??  

Regards to all

Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on February 06, 2019, 03:44:13 PM
Quick update!!

Cooling system now finished and filled. Water pump power supply fitted and working. I have to say that I was surprised at just how quiet the big Moroso electric pump is?

Next job is to fit the puller fan to the radiator and wire in the existing fan cables via the existing electronic temp sensor in the top hose.

I found that the tunnel ram manifold does not have a thermostat by pass. The new thermostat did not have a jiggle pin either. So I drilled three 5mm holes in the stat flange. This was fine to get the system filled and water flowing. I may just remove the stat and fit a restrictor disc though?

By manufacturing a custom bottom hose, I found that this will foul the alternator belt. So I took the alternator off and put it on the shelf. I will now run on batteries only. I will buy a pair of Excide 450/ 900dc batteries and buy the charger to go with them.

This actually means that I can replace the dished crank pulley (that I borrowed from my friends 350 SBC Volvo engine without him knowing) so he wont have a shock when he lifts the hood in the near future :)  

He is too busy with his Ford Pop Mopar project to even look under the hood of the Volvo 760 avec the SBC motor. ;)

I have to work next weekend and then a week of nights on a project for McQuarie bank in the UK. So maybe the weekend of 16th and 17th Feb will be more MGB stuff?

Regards to all

Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on February 27, 2019, 08:36:54 PM
Hi Guys!
Cooling system leaked water from the inlet manifold gaskets. I removed the Mr Gasket cheap cardboard gaskets and fitted Felpro.
They leaked as well.
Then I figured that the front and rear rubber valley seals were too thick.?  So I fitted new Felpro gaskets today and used RTV sealant for the valley seals, and then gently pulled the tunnel ram down on the bolts. I will go back to the workshop hopefully on Sunday after work to do the final torque down and then see what happens?

I seem to remember the manifold bolts needing 16ft / lbs?  Is that right!  I will look in my books to confirm if any of you cant tell me?

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on February 28, 2019, 10:56:24 AM
Perry, I've always torqued the intake to 15ftlbs first, then 25ftlbs with aluminum heads. As per Jeg's and Summit instructions.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on February 28, 2019, 03:14:20 PM
Thanks Jim!

I hope to get back to the workshop sometime after work on Sunday evening :)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on March 06, 2019, 03:46:14 PM
Bugger!

The new setup sealed very well. I was so paranoid that I even ran the water pump while putting a borescope into the dissy hole and viewing the front and rear water ports from inside the valley. Everything bone dry :)

Then when I stopped looking at the camera I saw a pool of water forming around the middle ports of the manifold on the outside. This was just on one side. Water was seeping out of an ally plug in the (what I call)  steam hole on one of the heads.

So I pulled it all off again and found that I had not used any Loctite on this plug as it was lose in the hole!

Both of these plugs have now been removed and re fitted with sealant. New gaskets are in my truck and I'm gonna fix it for good this weekend :)

Then I can start on the fuel plumbing !!

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on March 08, 2019, 09:15:08 AM
I'm sure you set the intake in on the heads & made sure that everything was square, flat, etc.  I had a set of heads shaved once & the they should have been angle cut to maintain the same angle with the intake.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on March 16, 2019, 07:06:45 PM
Today was a great day for me guys!!

Everything came together for 5 test runs in the workshop.

I still have a long way to go before the car will roll under its own power. BUT! todays test result was like a shot of adrenaline for me I must say.

Regards to all

Perry

https://www.youtube.com/watch?v=9ilG37GP5B8&t=6s
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on March 16, 2019, 08:15:42 PM
Perry, Very Cool!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on March 17, 2019, 06:12:50 PM
Thanks Jim!
I am very pleased to say the least :)

I cant wait to run it for longer when I have made the Zoomies.

This engine is solid mounted to the chassis with additional braces front and rear of the right hand cylinder head (as viewed from the front) as I used these on my old Rover V8. The amusing thing for me was that the rear brace bar bolted straight into the Brodix head. The front brace only needed one hole enlarged on the Clive Wheatley Bracket so that bolted on as well?

During the test runs this weekend. I could have placed a glass of water on the top of the slam panel for the bonnet and it would not have lost a drop of water. The rotating assembly balancing works have paid off big time I think.

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on March 30, 2019, 11:11:11 AM
Not sure how that new electric water pup will like a restrictor.  Seems it would be easier to hit your target temp with a thermostat & allow all the flow needed for cooling when needed.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on May 19, 2019, 05:21:00 PM
Another quick update!
Apart from still missing one door. The car is now ready to move under its own power. The fuel system is 90% complete with an open AN10 line under the hood. But I can still fill the carbs manually. my photobucket account is on hold right now as I cant seem to upgrade it? And my pics are too large to load on here.
I spent the last 2 weeks of spare time making the Zoomies which look ok. I got the fuel system well progressed. I had to have the prop shaft modified and got it fitted, I got the lexan rear screen fitted. I fitted a remote external battery kill switch. I fitted lexan to the drivers door. I got a remote fuel pressure gauge fitted to the scuttle in front of the windscreen. I will fit another gauge here for oil pressure soon, I got the breathers cut into the Brodix valve covers + lots of other small jobs done.
I only have 2 more evenings to work on the car as I'm off to SF on Friday to see family for a couple of days, and then me and the Wife are of to Vegas for 5 days before hitting SF again for 2 days before we fly home. Hopefully this resized attachment will work?

MGBengineresized.jpg
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on May 20, 2019, 06:46:06 AM
Perry, Thanks for the update!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on May 20, 2019, 03:43:38 PM
Hi Carl
I used a restrictor in the old Rover setup as well. It takes a little longer to warm up. But when warm (60C) before the burnout, the fans cut in as required. 60C into the burnout pad. A quick burnout = 70C. By the time I have staged it sits around 75C. by the time I finish the 1/4 mile the old Rover used to see 90C. Then back to 80C after the coast to the exit at the end of the track. Then 85C - 90C by the time I had cruised back to my pit area depending on ambient air temp on the day. If its a warm day I start at 50C.

If it was a road car I would use a stat.

Regards
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 10, 2019, 06:27:15 PM
Wow!!
May has turned into August already Guys ??

So much has happened since my last post.

Long story short!
I got the car running and went for a few test days at the track. Six days in total until last weekend.

I had problems galore with setting up the MSD Digital 7.

I got the car in some sort of tune that seemed to work.

I only managed a 10.2 on track with a lame tune.

Then I started experimenting with trans brake launches.

Then I made a mistake with the tune and broke an engine mount.

The Mopar Weekend at Santapod Raceway gave me valuable info for sure.

The MGB is no off track until 2020 so I can upgrade a few / lots of things before I attempt a full power launch on this new engine.

The recent test days have given me a big smile I must say. Despite me having to take the MGB off line for several months, I'm still happy because I know she will roll out next year and be very quick.

I will attach 2 slo mo vids of the reasonable launch, and the launch where I got it all wrong. There is also a TV clip from Santapod where you can see a real time vid of the engine mount breaking launch at 4 hours 33mins.

I'm very happy to have enough info now so I can get the MGB ready for next season at the track.

Regards to all!
See the vids and please give me your thoughts.

Pel

https://www.youtube.com/watch?v=t7mvCOKKu04

https://www.youtube.com/watch?v=F24pI44Zinc&t=35s

Fast forward to 4 hours 33 mins to see my last run in real time

https://www.youtube.com/watch?v=klLkaRjzbtQ&t=16484s
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on August 12, 2019, 08:37:52 PM
Perry, You forgot your wheely bars in the first video! You may be able to adjust you slapper bars to eliminate some of the twist. Some of the more powerful V8 street cars on this site put a rectangular tube between the front of the leaf spring and the crossmember. Look at Dan Master's build for an example. What part of the motor mount broke? The Speedway mount or the through bolt? Looks like a lot of fun!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on August 13, 2019, 06:43:12 PM
Yeehaw!  Bottoms up!!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on August 24, 2019, 12:49:10 PM
Hi Jim
It was actually the lugs on the block that sheared away on the even number side. So for my UK car the drivers side.
These lugs are proud of the block and seem to have cracked away where they meet the block. This allows the engine to drop one side by about 3/8" which caused no 8 plug boot to foul the steering shaft and broke the plug insulator. So only 7 cylinders after the first landing :)

I will get back on the car late sept or early October to start repairs. I've been away to Majorca with Grand Daughter Faith and now the Wife and I are in Crete for Grandad and Nannies week away on their own !

Work has built up since we left the UK on the 8th August. So I think I have the first weekend of Sept off and then it will be 7 days a week for the next 4 weeks to start with. I will try to gather some bodies for the first weekend of Sept so I can at least get the engine and drive train out of the car and on the stand for inspection.

Carl !
I  didn't lose my nerve despite not having been in the seat for nearly 5 years. I did try to pedal it to slow the initial drop. But the engine didn't want to catch up in time?  When I re view the vids I cringe when I see the front suspension taking that pounding.

Regards to all
Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on November 28, 2019, 05:16:16 PM
WOW!
So long since I posted?
I have now finished the passenger side mount. I have raised the gearbox tail by 20mm. Drivers side mount now 90% complete.

I am trying to get to the workshop for an hour or two during the week after work as U hive no weekend time free. BUT! This weekend I WILL finish the engine mounts because I'm 61 on Saturday. And my family rule is that on your birthday you can do whatever you want.

The family asked me what I wanted to do on my Birthday weekend so I told them..... I want to work on the car Saturday and then have a Chinese meal at home with you lot in the evening and play games around the table.

Then on Sunday I want to take you all out for a meal before we all hit the Cinema to watch Frozen 2. This is mainly because I want to take my Grand Daughter to see the Movie. But also, as I have told the kids, to be in the cinema with all my kids like back in the old days when they were young.

I told them all to NOT buy me any presents, but spend the money on their Cinema tickets instead. I'm happy with a card as I really don't need anything unless they all want to club in to buy me an LS engine or an 8/71 blower kit. :)

Its taken some time but I'm happy if I can have the car ready before Xmas so I can drive it out off the 4 post lift and into the other side of the hobby shop onto the 2 post lift. As I need the other lift to give my 2008 Grand Voyager a once over. It my new MPV and I love it so far despite a few little issues to deal with. I have my second Grand Child due on Feb 26 2020. So Grandads Taxi needs to be ready to rock for the annual family trip to France in April for Disney and Carp fishing ;)

I will get some pics and vids uploaded of progress asap.

Regards to all

Pel
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: kstevusa on November 29, 2019, 07:47:09 AM
Sounds like a great plan.  Have a Happy Birthday Perry!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on December 04, 2019, 05:45:53 AM
Perry, Happy Birthday! How did you fix your motor mount ? Have you thought about a 4 link rear suspension instead of leafs? Don't forget your Wheelie bars!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on December 06, 2019, 05:34:53 PM
Hi Jim!

For the time being a 4 link rear is out of the question. I'm on one of my old guy things again. I did say way back in the day that the old slugger would run 10's with a Rover V8. I did this and then pushed on to 9's on track. And I'm sure if I had fitted the wheelie bars back in 2014 the Rover MAY have run an 8 or very close to it ?

SBC fitted now for the 8 second attempt. BUT !  The cart springs MUST stay on the car for the 8 second attempt as well now. The cart springs are original MGB V8 items and they have taken a pounding over the years. I intend to fit new stock springs from the MG Owners Club parts dept to see if they will hold up for the 8 second attempts in 2020. They are not expensive and they seem quite sturdy.

I did talk to the tech guru at MGOC about this and he gave me all sorts of tech info about the spring rates etc. He also asked why I had not been providing articles for the club magazine for a good while about the cars progress?

I told him that I did say that when the MGB lost its Rover V8 and took the SBC on board I would consider it a kit car.

His reply was very nice. He said that my MGB V8 with its USA derived Rover V8 was a great car. He also said that the MGB V8 has now been fitted with another USA derived V8 engine. So just get on with providing updates on the cars progress again please. WOW!!  I was happy to hear that I must say.

I re joined the MGOC earlier this year to keep up with friends. I have posted about me wanting to attempt my 8 second pass in June next year at Santapod raceway and re forming my old MG Drag Racing Club. I have had a good response from MG folk wanting to get back to the track for racing + Show and Shine in my club stand next June. A lot of them have asked me to ask MGOC to see if they would like to make this a club event.  I will ask the club to see what they say.

I would love it if I could get the MG name back on site at the Drag Strip as an annual event like I used to back in the day.

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on January 20, 2020, 07:26:30 PM
Quick update folks!

Suspension repairs now done re broken front ARB drop links. Slapper bar mods now done. Wheelie bars now fitted and ready for testing in 4 weeks time.:)

(https://i205.photobucket.com/albums/bb270/mgbv8_photo/Wheelie%20bars%20welded%20in_zps6iweanf3.jpg) (http://s205.photobucket.com/user/mgbv8_photo/media/Wheelie%20bars%20welded%20in_zps6iweanf3.jpg.html)


(https://i205.photobucket.com/albums/bb270/mgbv8_photo/wheelie%20bar%20from%20side_zpsoizimir1.jpg) (https://s205.photobucket.com/user/mgbv8_photo/media/wheelie%20bar%20from%20side_zpsoizimir1.jpg.html)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on January 23, 2020, 09:01:46 AM
"Suspension repairs now done re broken front ARB drop links"

After I saw Steve Carrick's break at the ball joint end, I carefully tack welded mine.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on February 16, 2020, 03:57:29 PM
Only 1 week now until testing begins :)
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: ex-tyke on February 17, 2020, 08:44:11 AM
QuoteOnly 1 week now until testing begins :)
.......not if the current UK weather pattern holds.  :-(
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 13, 2020, 04:35:52 PM
Hi guys

A quick update!!

Wheelie bars need re working to get more adjustment and I fried the tranny on this day out just before lock down.

Real time vids then Slo Mo vids. The Slo Mo stuff explains all I think.

Regards
Perry

https://www.youtube.com/watch?v=twSTQ46BPug

https://www.youtube.com/watch?v=91KG3BKv_00&t=14s

https://www.youtube.com/watch?v=EIfsXpAp3Bc

https://www.youtube.com/watch?v=XvWq38zZ9tw&t=32s
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: MGBV8 on April 18, 2020, 10:03:33 AM
More front lift to plant the tires better?

Great to hear from ya, Perry.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on April 21, 2020, 02:15:10 PM
Perry, Time for the Powerglide upgrade? Keep us posted  on your progress!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 24, 2020, 06:37:42 PM
Exactly Carl!

The bar wheels hit down way too soon eh? They were just acting as levers to unload the rear tyres eh?

That will be rectified for next time out after the tranny rebuild.

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on April 25, 2020, 05:05:31 PM
Jim!
I was offered the use of the Glide from the Slingshot my friend runs Which I have also driven down to 9.4 on part throttle :) Damn! that's a scary thing to drive for sure. Sadly too much messing around to get it fitted for a trial run I think. I will wait for lockdown to end so I can get my 350 refurbished with better sprags and clutch packs etc. Then I can go testing again. I'm itching to get this thing back on track asap. I know I may have to wait until late in the season and weather may not be good when I can eventually roll her out again. Based on my old calcs of the old Blown and Nitroused Rover engine I am Sure that the car will run as low as 9.3 on the nasp SBC motor. I need to confirm that on pump gas and then try C16 fuel to see if it will do any better?
THEN I will have my baseline tune on both fuels for the MGB. If the car only makes say 9.4 on track I know that I can get into the 8's with a sniff of gas for sure. Exiting times are ahead for sure Guys!  Its all down to when lockdown ends and when I have the spare money to refurb the tranny.

Regards to all and please stay safe.

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: 427ZA on June 05, 2020, 05:29:25 PM
Pel!!
It's great to see the old fighting B back out on track at long last, it's been an epic journey for you and I hope those 8's come rolling in soon!
Have a chat with Paul at Edge Performance Transmissions. He has mine in for a complete rebuild at the moment and is also supplying a torque converter that's matched exactly to my car and drive-train so I won't drive through it at the top end or over power when launching and it will still be road friendly.
 They're really great to deal with and keep you updated through the process.
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on June 05, 2020, 06:01:53 PM
Perry, Thanks for the update!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: perrymgbv8 on December 27, 2020, 04:38:48 PM
WOW!
Over 6 months from my last comment Guys!

Sadly! I lost my job due to Covid. Its been a whirlwind of events since 30th June 2020. Two months of of being out of a job and then finding a new job with 50% less salary that JUST pays the monthly bills.

So the race budget is now shot to buggery for the time being eh?

I have managed to get my gearbox refurbished and I picked it up last week thanks to my friends at TCA transmissions in the UK.
The engine and tranny have been out of the car for several weeks. The engine is lame on cylinder 2 though. Number 2 still fires but when I put my hand over the zoomies when the engine is idling, Number two only gives my hand a gentle hot push instead of feeling like someone has whacked my hand with a bat.  

I will not know what the problem is until I do a compression test and then a leak down test eh?  I'm hoping that its not a ring issue with possible bore damage.?

The next part of the story is that I DO need to remove the cart springs and fit a decent 4-6 link rear end if I am going to find that 8 second timing ticket. Even with the lame number 2 cylinder, I think I can go sub 9 seconds with a new rear end fitted,

As money is now an issue due to redundancy, I will have to do whatever I can in 2021 to even get the MGB back on track for fun runs!

Regards to all

Perry
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: mgb260 on December 27, 2020, 08:40:06 PM
Perry, Thanks for checking in with us! #2 could be valves also. Art Morrison 4 link kit is what my brother used with his Vega ProGas. Perry, hang in there!
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: BlownMGB-V8 on December 28, 2020, 01:07:45 PM
Perry, you might pull your valve cover and check how much lift you are getting on #2. With flat tappets lobe damage is a thing.

Jim
Title: Re: Perry's Drag Race MGB is getting a SBC engine now !
Post by: Anarchy99 on December 28, 2020, 06:49:50 PM
I love reading this thread. I'm definitely thinking about the same type wheelie bar setup for my sprite as I'm finishing it up again soon. Repairing front ends gets old in a hurry.