BritishV8 Forum

General Category => MG Sports Cars => Topic started by: mgbsandiego on October 06, 2008, 06:18:42 PM

Title: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: mgbsandiego on October 06, 2008, 06:18:42 PM
Hi guys - getting round to cut the holes in the inner fenders for the RV8 style exhausts to exit and wondered if anyone had a template / approx measurements to save me from getting it wrong and performing my normal "hatchet job"

Cheers - John
(75 B)
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: rficalora on October 06, 2008, 10:39:33 PM
John, there are so many variables you probably need to provide more information -- like whether you have a BOPR variant motor or something else & whether the motor mounts & headers you used came from one of the typical suppliers.  Even with that it may be a long shot.
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: Simon Austin on October 07, 2008, 01:40:34 AM
John,

If it helps you out, when I had the holes cut for my RV8 headers, all my body man and I did was have the engine installed and slowly lowered the headers while he cut out (with a plasma cutter) gradually larger holes around the header until the size was correct when the header was in place.

Here's a pic of the finished product.
DSC00318.JPG
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: mgbsandiego on October 07, 2008, 01:03:57 PM
Thanks guys for replying - DUH!! - where was my brain - yes I should have given some more info like the type of engine (Rover 4.2) / headers type / engine positioning  - you are quite correct, quite a few variables as to where the headers will exit.

Great picture Simon - thanks, this gives me a good starting point and yes I think that lowering the engine and working the exit hole from there is perhaps the best approach.

Thanks again - John
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: Moderator on October 07, 2008, 02:17:09 PM
Here's a glimpse of what the holes look like on British Motor Heritage reproduction RV8 panels:
(http://www.britishv8.org/Articles/Images-V16-1/MGB-Bodyshell/A.jpg)
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: mowog1 on October 07, 2008, 04:53:31 PM
Somewhere I have a template for the RV8 header adaptation needed for a BOPR....I'll try to find it.
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: mgbrv8 on October 07, 2008, 07:22:48 PM
What fender flars are you running they look great.

Dave
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: mgbsandiego on October 08, 2008, 07:34:32 PM
Thanks all - John
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: kenzmyth on December 09, 2008, 11:00:19 AM
Hello All,

I am a new member with a 1966 MGB Roadster V8 conversion project I bought from a friend. He has done all the engine compartment mods and bought RV8 style exhaust headers for the Rover 3500/SD-1 conversion project, so I am keenly interested in those templates for the exit holes. Please let me know who has them and how I might get them. Also, the areas of the engine compartment over the original lever shocks, which need to be modified for clearance, were removed, completely. Since it looks like a fairly complex, compound
curved area, anyone have any suggestions for filling them in? I am not a great metal fabricator, so I'm wondering if there are engine compartment sheet metal replacement parts available. Moss Motors doesn't carry them.

Thanks, Ken.
Title: Re: MGB - inner fender template to cut holes for RV8 style exhausts
Post by: rficalora on December 09, 2008, 10:31:54 PM
Ken, send a pic of the area you need.  I got the inner fenders from a car that was being parted out; if the part you need isn't the part I'm using, you can have them for the cost of shipping.