BritishV8 Forum

General Category => MG Sports Cars => Topic started by: 74ls1tr6 on March 14, 2014, 01:30:08 PM

Title: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 14, 2014, 01:30:08 PM
Our GT is on all 4 wheels as of today! I just got done yesterday welding and fabricating the rear suspension attachment points. This suspension setup front and back is from Ted Lathrop at Fast Cars. Very pleased, and nice products Ted!

Here is some photo's of the GT on the ground.


I will need to relieve some turning area just behind the front tires at full lock.
2014-03-1409.32.38.jpg

2014-03-1409.33.01.jpg

The rear tires don't look like much flare is needed, but yes it is needed for suspension travel.
2014-03-1409.33.09.jpg

Looks like I will have 1 3/8" from the flattened bump stop to the tire in the rear. That should be enough room for suspension to move. These tires and wheels are the same size as on our TR6. The MG wheels are 1/2" wider is the only difference, and same size tires. The tires are 245/45/17 Yokahama S drives.
2014-03-1409.43.29.jpg

Trying to keep this project moving along at a good pace. This project started just after we go home from the Omaha meet.
Title: Re: A nice milestone for Brenda's GT build
Post by: kstevusa on March 14, 2014, 01:50:58 PM
Calvin, look great!  Guess Brenda will possibly show up in the NEW RIDE, when?  Man it looks good. SAFETY FASTER l
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 14, 2014, 01:58:24 PM
More photos!

Attachment points for the Panhard Bar. Extended the cargo area where the back seat was. You can also see where a square hole is cut for the top of the Panhard bar bracket, to be welded to the frame rail. The triangular bars are so that the frame rail won't bend under hard cornering.
2014-03-1409.45.25.jpg

Center link attachment point and driveshaft hoop.
2014-03-1409.44.21.jpg

Panhard bar attachment at a different angle.
2014-03-1409.44.10.jpg

Lower link attachment point. The new frame rail bracket link attachment point has been dropped down some for better tire bit.
2014-03-1218.49.24.jpg

So far everything is looking good. Next will be to fabricate a bracket on top of the driveshaft tunnel to strengthen the top link attachment point. I will be moving the e-brake from the side to this bracket on top. It's fun to move this project at a good pace!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 14, 2014, 02:01:01 PM
Thanks Kelly,

It won't make it to 2014 meet, but maybe 2015 :-)
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on March 14, 2014, 02:25:33 PM
Calvin, Excellent work!
Title: Re: A nice milestone for Brenda's GT build
Post by: mowog1 on March 14, 2014, 04:17:58 PM
Nice!!!   Ford 8", I presume?
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on March 14, 2014, 08:14:58 PM
Of course it's an 8 inch.  That's Ted's favorite for the MGB

Making good progress, Calvin!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 14, 2014, 09:50:24 PM
Yes Rick, Carl is right, and you knew also it is an 8" differential.

Have come to a close of the work day on the GT. Finished fabricating the strengthening bracket for the top link area. Figured a way to install the e-brake while the bracket is welded to the tunnel, just incase for maintenance. Welded four taps with the nut welded to the back tap in two places. The e-brake will slide in from the top, the lower hole that is drilled, is for installing the pin, to hold the cables going through the body tub. Using a Lokar e-brake handle, almost looks like a TR6 e-brake handle.

You also can see some previous owner cut part of the inner body for a make shift speaker hole. I will install a speaker there, but will need to brace the area to keep the structure integrity(between the back door jam and inner wheel well).
 
2014-03-1418.04.31.jpg


2014-03-1418.04.48.jpg


2014-03-1418.05.05.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: rficalora on March 14, 2014, 11:08:59 PM
Looking good Calvin!
Title: Re: A nice milestone for Brenda's GT build
Post by: Preform Resources on March 15, 2014, 06:15:17 AM
Nice fab work Calvin ! is that a black epoxy base coat on everything ?
Dave
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 15, 2014, 10:13:29 AM
Thanks Rob & Dave,

Dave you are right. The blasting company sprayed high build black epoxy base coat primer. They gave me the option between black or gray. I picked black because I have gray. I figured it would be easier to find the high spots when doing the  body work.
Title: Re: A nice milestone for Brenda's GT build
Post by: TR6-6SPD on March 15, 2014, 12:44:07 PM
Calvin,
The car's looking great! We need more photos of Brenda getting her hands dirty.
Question. Do you find it an issue at all of having to clean a weld area of epoxy primer, before you can actually weld. In other words, do you think it might have been better to leave it in bare metal?
Ken
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 15, 2014, 03:53:11 PM
Thanks for the comments Jim N,

Hi Ken,

I would be better to have bare metal, but for as long as this project will take, I was having some surface rust showing up. So it good that is there but it is a pain to clean the area before welding.

So to answer the question, If you do all welding in a short period of time, it would be better to not have the primer.

I did think of this before they sprayed the car! Went with the primer route.
Title: Re: A nice milestone for Brenda's GT build
Post by: Dan B on March 15, 2014, 04:08:01 PM
Have you ever used "weld through" primer?  I saw it on one of those tv shows.
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 15, 2014, 07:55:10 PM
Hi Dan,

That is the question I had for the blasting shop. They said No, we don't have that primer here. So that did cross my mind at the time too.
Title: Re: A nice milestone for Brenda's GT build
Post by: lawnvett on March 15, 2014, 07:58:56 PM
I like it, a you hoping to finish it in one year?
Title: Re: A nice milestone for Brenda's GT build
Post by: RMO 699F on March 15, 2014, 08:10:41 PM
Calvin...you have done some really great work on your car....Can not wait to see the finished product!
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on March 15, 2014, 10:46:00 PM
Calvin,

Looks great...you're making great progress!!
Title: Re: A nice milestone for Brenda's GT build
Post by: BlownMGB-V8 on March 16, 2014, 10:24:20 AM
I heard that "weld-through" primer was a compromise. Not very good to weld through and maybe not a very good primer either. But then maybe that was just a rumor...

Jim
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 02:47:46 PM
PJ, It is always nice to say one year, but we all know it does take longer than that. The good part about this build is that we have probably 85% of the parts already.

Scott, Is our engine in the same place as yours??

So today we thought of test fitting the ls1/T56 in the engine bay. It went right in, with grinding the front lip off the middle cross member. The engine is sitting on the rectangular bosses on sides of the block, right on the frame rail, and just in front of the front bolt holding the suspension. Of course with Teds front suspension the Camaro pan just slid passed his cross member.

Here are some photos:

Okay, This photo was some of Brenda's humor, figuring it would help to get it in there!


2014-03-1611.23.49.jpg

The modifications that were already done before attempting test fit, frame rail mod on both sides, and firewall cuts.
2014-03-1611.08.16.jpg

The water pump fittings will be taken out, and tapped for 90 degree fittings like we did on our TR6.
2014-03-1611.08.00.jpg

There is 1 1/2" between the stock firewall and the passenger head which sets back farther than the driver side.
2014-03-1611.08.29.jpg

Some more photo's to follow showing fitment!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 03:08:46 PM
I believe the stick shift will work just fine right there.

2014-03-1611.45.28.jpg

The engine oil pan and the steering rack are about the same distance from the ground.
2014-03-1611.07.36.jpg

A photo taken from the hatch area to show where the heads sit at the firewall. I'm really surprised that the T56 Reverse Lockout Solenoid clears in the tunnel. The T56 has plenty of room without any modifications to the tunnel. The only issue I saw was the transmission tie in cross member will be back by the frame cross member. So to use the original cross member bolt holes a unique cross member will be fabricated.
2014-03-1610.50.11.jpg

Made for an ls1, looks like it should and was meant to be in there.
2014-03-1611.08.56.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 03:25:57 PM
Passenger side header clearance

2014-03-1610.45.18.jpg
Driver side header clearance.
2014-03-1610.45.04.jpg

Driver side.
2014-03-1612.11.06.jpg

passenger side.
2014-03-1612.10.54.jpg

I think from the rounded area of the inner wheel well panel, it can be re-formed at a 45 degree since with Teds front suspension clearance on the other side. The area right in front of the spark plugs, the first two plugs, just maybe run headers down through between the frame rail and block. Will need to look at that a little more.
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on March 16, 2014, 03:39:47 PM
Calvin, I like your idea of flattening the rounded area. Still looks tight between engine and frame. On the other hand you could just cut it out there for RV8 thru the fender headers and the hole would let some engine heat escape.
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on March 16, 2014, 04:00:42 PM
Steering shaft routing looks interesting. :)
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 04:23:22 PM
Jim after looking at the header area, I think I will go down through the inner fender wheel wells. looks like plenty of room going that route.

As Carl noted that the steering routing looks interesting. If I go the RV8 header route, the steering shaft will be a straight run down to the rack.

Photo taken looking at the routing for the steering rack to the column firewall.
2014-03-1613.06.17.jpg

Black cap on steering rack shaft.
2014-03-1613.05.54.jpg

This photo taken inside where the steering column would be close to the firewall. It looks like a straight shot to the black plastic cap on the steering rack shaft end.
2014-03-1613.08.11.jpg

It looks good doesn't it Carl, the routing? One u-joint at both ends should do it. The only issue would be the motor mount?
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on March 16, 2014, 05:55:16 PM
Front motor mounts?
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on March 16, 2014, 06:09:27 PM
QuoteScott, Is our engine in the same place as yours??

Calvin,

This should show the differences.

LS4EnginePositionCalvinCompare.JPG

It looks like I'm about 1.5" further back and a little less than an inch higher than you are. Is the engine tilted rearward at 3 degrees (or what ever the angle you're using) in your pics?

This is a great way to compare an LS1 conversion with a stock cross member as opposed to a Fast Cars front end. You have a few more options. If I placed my engine where yours is I would be looking at lowering the steering rack. Avoiding moving the rack was one of the goals I had for this conversion.

An LS1 looks like it belongs in the engine bay of a B, doesn't it?

Must be exciting to see the engine in place, I know it was for me...still is. :)

Scott
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 07:35:10 PM
Scott, measuring just about 1 1/2" back farther than our engine. The further you go back the better I think to achieve 50/50 weight distribution.

Scott, buy the way your ls4 has the great flowing 243 heads I see. Those heads are the same ones I'm using on the TR6, but CNC ported with larger valves. These heads flow very well in stock form!!

If I go back 2 more inches I would need to revise the tunnel area some( T56 transmission BIG), deal with the stick shift needing to be moved forward, which I just may do for the better handling.

It is exciting to see the engine in there, and it looks good.

Scott, So your original firewall is flush with the passenger side head right?

I did measure a 3 degree down towards the back of the transmission as it sits now. I will need to take off the Reverse Lockout Solenoid, do the modification and not use the solenoid + most of the housing, that I did on the TR6 T56. Then I can go back the 1 1/2" or 2" for the engine. I will need to come up like you did off the frame rail, because right now the T56 is resting on the frame cross member.

This kind of what the front end will look like to give an idea of how the flares will look. Anyone want to guess what donor car was for the flares?????    Rob F knows what we're using if he remembers?
2014-03-1615.42.25.jpg

Brenda is getting excited when I showed her this with the panels on.
2014-03-1615.42.39.jpg

These flares will open up the wheel well some to match the tires and for turning radius. These flares have a lip on them at the bottom by the rocker panel. I might just run a rocker panel skirt to match them between the flares.
2014-03-1615.43.16.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on March 16, 2014, 08:28:21 PM
Calvin, are those the Datsun Z flares that fasten from the inside?
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on March 16, 2014, 10:33:00 PM
QuoteScott, So your original firewall is flush with the passenger side head right?

Calvin,

No, I had to cut about 3/4" from the firewall on the passenger side to make room for the head setback so I could get the engine behind the steering rack. You can see what I've done in the first picture, the second picture has the engine in place.

LS4Firewall2.JPG
LS4Firewall1.JPG

If I could have gotten away without cutting the firewall and still accomplish my goals I would have. 2" isn't going to make much of a difference at all weight distribution wise and you already have lightened up your front end with Ted's cross member. I'd be asking myself if it was worth the work...maybe it is to you and that's cool. I thought I would point it out anyway.

Oh, your car has a real nice stance! Can't wait to see it done!

Scott
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 11:12:54 PM
Jim, "great guess" they are from the same family. So that others don't need to guess, they are 1995 Nissan Stanza flares. I got the idea on this site, since there wasn't any, rabbit flares, Dodge Omni  flares available in the area. I think this was the same problem Mike Cook had in obtaining flares.

Mike Cooks Silver Lady and his write-up using 1995 Nissan Stanza Flares............

http://www.britishv8.org/Articles/Nissan-Fender-Flares-for-MGB.htm

I had gone to a recycle yard and pulled four front fenders from  two 95 Nissan Stanza's, paid $15 for each fender. I used a plasma cutter and whacked them off and got rid of the remaining fenders.
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on March 16, 2014, 11:19:15 PM
I might have to copy the Sentra flares, looks like great fit!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 11:20:22 PM
You are probably right Scott about the extra work. I do need to kind of install everything in the engine bay, to see if I need to move the engine back or not. So this evening I was installing the new front runner system to see if all is good. It's good so far!
Next will be the Radiator and Fan.

It is very tight for the motor mounts "Dang"!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on March 16, 2014, 11:36:16 PM
Jim Stanza flares. I think the Sentra flares are pretty small, but I may be wrong?
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on March 16, 2014, 11:39:51 PM
Calvin, Yeah I know I  was typing while Skypeing the wife and was just going to correct it. Thanks again for a wonderful job documenting the build!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 03, 2014, 10:08:38 AM
Making some more progress!

Cut off the ends of Teds sway bar blocks so there will be room for radiator clearance
2014-03-3011.35.35.jpg

Moss's sway bar brackets didn't fit Teds holes, so welded some more metal on there for fitment.
2014-03-3011.40.13.jpg


2014-03-3013.31.34.jpg

Motor mount block plate modified so that round mounting tube would be closer to plate. Cut off the ends and welded up and re-drilled the bolt holes.
2014-03-3016.01.50.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 03, 2014, 10:21:09 AM
Motor mounts welded up.
2014-03-3016.01.59.jpg

Re-drilled and ground for frame rail clearance. Driver side
2014-03-3018.24.53.jpg

Passenger side....Yes this is a Pyr- Ls1 block. Makes mocking up a lot of stuff way easier as you will see in more photos.
2014-03-3018.25.06.jpg

Motor mounts welded to the frame. Welded to the top and down the side of the frame rail, made out of 2"x4" 1/4" thick steel. The position for reference is over the back front suspension bolt that goes through the frame.
2014-04-0613.10.06.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 03, 2014, 10:39:16 AM
Reference photo of where the engine blocks resting place with a 3 degree down on the back (passenger side view). I have the transmission bolted up to the hard foam block and in the car. The back of the T56 is sitting on the cross member behind the transmission mounting bracket area. That area will need attention. The rectangular reference point is about 1" above the bolt hole surface. The outside edge is inline with the inside of the bolt hole for the suspension.
2014-04-0613.10.17.jpg

Top view of driver side.
2014-04-0613.10.34.jpg

Underside view.
2014-04-0613.13.45.jpg

Underside view.
2014-04-0613.13.55.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 03, 2014, 10:51:51 AM
Moved the fire wall back and started to fill metal back in.
2014-04-0706.28.36.jpg

Photo of inside showing Transmission tunnel being raised.
2014-04-0706.27.53.jpg

Dark night photo of the fire wall showing where tunnel was raised.
2014-04-0706.27.40.jpg

Motor mounts, firewall half completed.
2014-04-0615.28.45.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 03, 2014, 11:04:47 AM
Using ice engine works mocking blocks to make the headers( 1 3/4" primaries). These blocks make it incredibly easy to fab up the headers. Driver side.
2014-04-3017.42.38.jpg

Passenger side.
2014-04-3017.42.45.jpg

Four into one header. I might try to lengthen the primaries down some depending on tire clearance.
2014-04-3017.42.57.jpg

The starting of header mocking blocks to stainless steel. So far so good!
2014-05-0217.16.53.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: lawnvett on May 03, 2014, 06:34:37 PM
you are making great progress thanks for all the documentation.
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on May 04, 2014, 08:33:54 AM
Fantastic progress Calvin, looks great! Thanks for sharing!
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on May 04, 2014, 08:52:07 AM
Hey, Calvin great work as always! Did you trade the front air dam for one of Dave's new bumperless one?
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on May 04, 2014, 09:03:43 AM
Calvin

Just for reference, how about a pic straight down showing the firewall to engine clearance?

Your work makes it looks like you are in the business!
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 05, 2014, 01:15:21 PM
Thanks everyone for the compliments it helps all of us to keep moving on.

Jim, I will pay the difference for when Dave C sends me the front Valance without the bumper indentation.

Carl the next post should show you what you are looking for at firewall clearance.

This bad boy took two full days to fab up.

2014-05-0318.34.37.jpg


2014-05-0318.34.49.jpg


2014-05-0318.36.12.jpg


2014-05-0318.35.14.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 05, 2014, 01:22:53 PM
Here are the photos for firewall the engine clearance. Have plenty of room to get at the back plugs.


2014-05-0506.38.34.jpg


2014-05-0506.38.40.jpg


2014-05-0506.38.49.jpg


2014-05-0506.38.57.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on May 05, 2014, 06:26:37 PM
Calvin, Headers are a work of art! What do you plan on the rest of exhaust?
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 05, 2014, 06:46:11 PM
As far as the rest of the exhaust, I'm torn between using round pipe, or oval pipe for more under car clearance. I like a somewhat low ride but not liking the idea of dragging pipes on the ground.

I will probably run along the inside of the frame rail, make 90 degree bend behind frame cross member (towards center of car), then a sharp 90 degree bend into X-pipe, into low profile round or oval Spintech muffler or mufflers, and towards the end glass pack tips to keep sound down being a 2 1/2" will be loud anyway. The bigger the pipe the louder it will be. The ls1 likes to flow lots of air.





2014-05-0318.35.57.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: mowog1 on May 05, 2014, 08:59:48 PM
Awesome job and great pictures!

Thanks!


ThumbsUpFrontView.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on May 06, 2014, 04:53:48 AM
Calvin, it looks like you moved the engine back a bit more compared to the picture on the first page. How much further back did you go?
Title: Re: A nice milestone for Brenda's GT build
Post by: rficalora on May 06, 2014, 06:58:43 AM
Great progress.  The motor looks wider than I realized... Bet working on the headers was fun.
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on May 06, 2014, 07:47:17 PM
Scott,

I did move the engine back 1 1/4" and up an 1" for it's final resting place. This will make the steering shaft a true straight shot using a u-joint in the cabin and one at the rack. The shifter is not a problem. Also giving a little more room to work with up front for the intake air run.

Thanks Rob, It is wider than the 302 for sure.
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 06:30:48 PM
A few have asked how is Brenda's GT coming along, so here is some updates!

Worked on upgrading the LS1 with some good products.


Installed new LS6 ported oil pump along with Cloyes(adjustable) uprated timing gear set & chain. There is a visible difference in chain size for strength and gears are better machined. Set the gears up to stock setting and will let the cam run the advance that is ground in. The oil pump (not shown) will go over the crank small gear to drive it. 4 bolts hold it on.
2014-08-2914.26.45.jpg

This is one of the 241 LS1 heads that came off and it is stock valve size.
2014-08-3110.23.11.jpg

You can see the difference in valve size to the new PRC as cast 225 heads. These heads will out flow the heads on my TR6 quit a bit. Also you can see the blending of the chamber. These heads are 62cc chamber size. With a stock gasket will get about 10.8 compression.
2014-08-3110.23.25.jpg

A 12 pound aluminum fly wheel with ARP bolts. Will be using a spec 2 + clutch and disk. Good for 550 hp.
2014-08-2816.08.11.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 07:15:54 PM
This is one of the intake ports(of the PRC as cast 225 heads) that show the bolt going down into the intake port. That bolt needs to be sealed good or the engine will make blue smoke out the exhaust on deceleration. With an opened up intake port (cnc or as cast heads for lsx engines) the rocker stand bolt holes go through into the intake ports. That is why my TR6 smokes blue because I need to reseal those bolts again.
2014-09-0112.13.57.jpg

Change over to ARP rod bolts (ARP bolts in this photo not stock). This is a week link in the LS1 engine. If you plan on running your rpm up higher than 6500, It is recommended to change out the stock rod bolts. Procedure is to take one bolt out at a time and install a new one in it's place and torque to specs.
2014-09-0711.25.06.jpg

New cam is installed. This is a  228/228 duration 588/588 lift 112 LSA from Texas Speed. New LS7 lifters and new uprated push rods. Also installed Comp Cams trunion upgrade to the rocker arms. At higher lift cams or higher rpm will cause a problem with the needle bearings to come out and end up in the oil pan or damage the engine. Highly recommend this upgrade for insurance that it won't happen.
2014-09-0711.25.18.jpg

Timing chain(it is bigger and stronger looking than the stock one). You can see the oil pump hole that the pick up tube goes into. The O-ring that goes in there can't be pinched or wrong O-ring, will cause low oil pressure. So care needs to be taken with this O-ring.
2014-09-0711.25.31.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 07:47:48 PM
All the ARP rod bolts installed and torqued to spec. Both timing cover and back cover are aligned, so that the crank seals won't leak, and the oil pan won't leak when installed.
2014-09-0711.25.38.jpg

Next the crank shaft splash guard. You can see where the pick up oil tube will be bolted to, the second stud on the left from the bottom of photo. The oil pick up on a Camaro is in the back portion of the block, great for cross member clearance.
2014-09-0711.27.11.jpg

ARP oil pan bolts. You can see where the bolts go for the side main bearing caps. Ls1 aluminum blocks have 6 bolt main caps. 4 going into it and 2 on the sides of the block.
2014-09-0714.14.37.jpg

Ls1 oil filter tucked very close to the block, a great swap engine tight and compact. Also a better photo to show the side main bearing cap bolt in the counter sunk bore hole.
2014-09-0714.14.53.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 08:21:53 PM
This is almost ready to come off the engine stand. You can see my custom fabricated 1 3/4" primary stainless steel headers (these took big hours of work to make). Used new ARP head bolt which can be re-used unlike stock LS1 head bolts. Stock head bolts are stretch to yield type bolts. Used ARP SS intake bolts. Used new ARP header bolts. Found a used Fast 92mm intake that was hand ported by Vengence Racing, from a guy around here on ls1tech.com parts section list. I knew the guy from a previous purchase. New Nick Williams 92mm Throttle body. Will start the engine with the stock 28lbs injectors, but soon after installing 42lbs injectors. I will need to get into the ls1 computer with my HP tuner software and change the numbers for the new injectors. Then flash the new numbers to the computer. Will be changing the ls1 coils to truck coils too. Will keep the stock fuel rails which are good for 500hp.
2014-09-0115.37.31.jpg

Photo of the other side of engine.
2014-09-0115.37.42.jpg

Will be using Vintage Air front runner assembly which compliments the engine bay real nice. It comes with a ATI super damper on the crank. It is a beautiful piece.
2014-09-0818.26.01.jpg

Stock fuel rail with stock fuel injectors, soon to be changed after first start up.
2014-09-0115.38.09.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: kstevusa on November 17, 2014, 08:33:35 PM
Looking Good, Calvin     appears you have the LS1 by the b_lls, I mean testicles  :-)
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 08:48:48 PM
Here is the Super Damper and using a reusable ARP crank Damper bolt.

2014-09-0714.14.27.jpg

Didn't take long to get the car off the rotisserie and the front and back suspension installed.
2014-10-1209.04.42.jpg

Installed the engine and transmission all in one. Have some photos that I need to resize of Brenda helping me installing the engine. I'm under the car installing the bolt in cross member I fabed up. I already have the drive line cut down with new u-joints on both ends and balanced. Need to re-size some photos to continue. So the drive train is all done. I used a Camaro 3" aluminum drive shaft. I need to relieve or make a little more space at the transmission u-joint area. It is a roller now.
2014-10-1212.29.17.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on November 17, 2014, 08:53:36 PM
I'd take the sawzall to my car for that engine!  :)
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 17, 2014, 09:01:12 PM
Carl ....plan your cuts!! ;)
Title: Re: A nice milestone for Brenda's GT build
Post by: mgb260 on November 17, 2014, 09:11:38 PM
Calvin, looking Good!  Looking forward to the air dam and flares!
Title: Re: A nice milestone for Brenda's GT build
Post by: Scott Costanzo on November 18, 2014, 04:39:20 AM
Looks great Calvin! I suspected you were busy getting things done! :)
Title: Re: A nice milestone for Brenda's GT build
Post by: TR6-6SPD on November 18, 2014, 07:09:58 AM
The car is OK but I do like the S.S. fridge in the garage.
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 18, 2014, 10:22:50 PM
That Fridge is stocked up with Salmon(from this years fishing) Beer, wine & water. I don't know if anyone saw me lying on the ground under the car photo, but look in the Garage, on the wall in the middle between the cabinets, there is a LCD TV to watch Mavtv. I thought Ken would like that too.  ;)

Ken Percival came by last week and dropped off a 1963 MGB Aluminum hood that is real light. He also brought over a fiberglass TR6 hood. So I gave him some parts he needed. Ken will be moving 12 hour drive away to Idaho. There is a thought move out of California?
Title: Re: A nice milestone for Brenda's GT build
Post by: Moderator on November 19, 2014, 01:22:41 PM
Have I mentioned lately how awesome this thread is? The latest photos look great, Calvin!
Title: Re: A nice milestone for Brenda's GT build
Post by: HealeyRick on November 19, 2014, 07:44:07 PM
This will be a beast.  Always enjoy following your progress, Calvin.
Title: Re: A nice milestone for Brenda's GT build
Post by: mowog1 on November 19, 2014, 08:56:13 PM
Have you thought about a removable slam panel, Calvin?

Makes installation/removal of the engine a LOT easier.

SlamPanel_4.jpg

Whatslampanel.jpg

SlamPanelRemoved.jpg

RadiatorSetup_1.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: lawnvett on November 19, 2014, 09:05:27 PM
Gonna be a fantastic car, I'd love to go for a ride one day.
Title: Re: A nice milestone for Brenda's GT build
Post by: MGBV8 on November 19, 2014, 09:14:26 PM
A ride? Not what I had in mind. ;)  Oh, Brenda.....can I pretty pleeeeese.....
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on November 21, 2014, 10:50:35 AM
Rick, I did think of doing what you did, but the bolt in cross member worked out well for me. Not as easy as your setup but easy with one swoop and its in there.
Title: Re: A nice milestone for Brenda's GT build
Post by: Charles on November 21, 2014, 08:24:09 PM
Calvin, Thanks for sharing, and please thank Brenda for taking the pictures also. I have looked through all of the pictures now will be 4 times, GREAT.
charles
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 25, 2015, 07:02:06 PM
Getting some stuff done!

Centered the Aluminum fuel tank that I purchased from Curtis. Drilled the holes right at 3" over to center tank. This will allow for dual exhaust.

Couple of photos of it mounted in the car.

2015-01-0518.06.21.jpg


2015-01-0518.06.49.jpg

The small hole is for the fuel vent , which I'm going to install a roll over vent fitting. Then a hose will be routed out under car.
2015-01-0518.07.06.jpg

Finished welding in metal.
2015-01-0915.38.23.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 25, 2015, 07:19:20 PM
This is where the in tank fuel pump is located. It is in the front of the tank in the corner on the passenger side. Nice easy access door.
A few photos of the pump, the plumbing in a 8"x 8" box, that the return line dumps fuel back in to keep full at all times. It is about 3/4 deep in the tank. That is a Walpro 255 lph fuel pump, that I upgraded to a 340 lph  Areomotive fuel pump with the same form factor as the Walpro pump. So it fits with the plumbing correctly.  

2015-01-0910.26.33.jpg


2015-01-0910.29.21.jpg

Fuel sender unit mounted in there.
2015-01-0910.29.31.jpg

The plumbing is all in 3/8" tubing and AN fittings.
2015-01-0910.29.48.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 25, 2015, 07:33:56 PM
The feed and return are market well.


2015-01-0910.30.08.jpg

New Aeromotive pump number.
2015-01-0910.30.26.jpg

Pump out of tank, ready to install the new pump.
2015-01-0910.34.09.jpg

There is a rubber seal that mounts on the bottom of the fuel pump for vibration, and noise reduction. It fits right on the half round flange at the bottom of the tank. This Aeromotive pump is good for 550 HP fuel injected engine.
2015-01-0910.40.03.jpg

More to come soon. I have been working on the exhaust under the car too.
Title: Re: A nice milestone for Brenda's GT build
Post by: psmg on January 25, 2015, 07:36:26 PM
Calvin,
I used the same tank but also fabricated an access panel in the trunk floor to allow entrance to the fuel tank . I had to replace a fuel guage sending unit and cut a hole in the trunk floor rather than drop the tank. Easier to do now rather than after completion.  That should be one nice ride when finished.
Paul
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 25, 2015, 11:08:30 PM
Hi Paul,

That is a great idea to have an access hole in the trunk. I will follow your lead on that idea. I was thinking of the same when I was typing this all out. You just confirmed my thoughts.

Thanks
Calvin
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 25, 2015, 11:44:26 PM
Here is what I came up with to run the exhaust. The diameter of the pipe is 2 1/2" stainless steel pipe from the header collector to the exhaust tip. I was looking for some ground clearance, so here is what I came up with. I needed to add an X-pipe in there some where, so I put it across instead of front to back. I'm using the space under the seat area for two Spintech mufflers (low profile). Going to the back coming out of the X-pipe will be two 90 degree turns, into the mufflers. Then it will go under the axle then back up closer to the trunk floor into some stainless steel resonators, then to some tips. Haven't looked close enough to see if I can go over the axle. I hope I can run over the axle. I would like to hide the exhaust as much as possible.

2015-01-2512.11.32.jpg
C-channeled the frame rail on both sides. Reinforced the rails close to the floor with steel plate to the bolt in transmission mount. Also welded in some square pipe going through the frame rail for gas line, battery cable, and wiring. I will make cover's on both sides of the frame rail on the floor boards to protect the lines and wiring.

2015-01-2512.11.47.jpg


2015-01-2512.11.56.jpg

That is a 3" aluminum drive line.
2015-01-2512.13.07.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 26, 2015, 12:14:57 AM
Here is the pass through for the fuel line etc.
2015-01-2512.13.17.jpg

Some have been asking where is Brenda with this build, so here she is getting excited about the engine going in. # 1
2014-10-1211.12.57.jpg

#2 Polished up the bell housing some!
2014-10-1211.13.04.jpg

#3
2014-10-1211.13.19.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 26, 2015, 12:28:30 AM
The shifter was set pretty far back, so I got a shifter that moved 1" to the left, and 3" forward to put it in the right place.

2014-10-1215.53.45.jpg


2014-10-1215.53.52.jpg

Had to cut the hole back some, put some access holes for the allen screws, for the top plate. Installed a short shifter on there, should work just like the TR6.
2015-01-0606.59.34.jpg
Title: Re: A nice milestone for Brenda's GT build
Post by: rficalora on January 26, 2015, 12:36:02 AM
Looking good Calvin - great progress.
Title: Re: A nice milestone for Brenda's GT build
Post by: 74ls1tr6 on January 26, 2015, 12:43:26 AM
Hi Rob,
Have you had time to rebuild you h2o softener?
Title: Re: A nice milestone for Brenda's GT build
Post by: rficalora on January 26, 2015, 08:12:25 PM
I must have hit reply via PM... Have a look, should be good for a laugh.  But, short answer is yes, got it rebuilt and it's working now.  Great to have water in the mornings again.  Thanks to both you and Brenda for helping me on it!