BritishV8 Forum

General Category => MG Sports Cars => Topic started by: v8bloke on January 17, 2014, 12:42:08 PM

Title: Which rear end for 400bhp MGB
Post by: v8bloke on January 17, 2014, 12:42:08 PM
I am worried that my latest engine modifications ( TA heads for my 4.8 rover ) will be too much for the stock axle and composite springs.
Planning on a 3 link with coilover shocks and mumford link.

Have searched the net and have found conflicting views.
My requirements are simple, it needs to be strong enough for say 450bhp (one day) but at the same time as light as possible.
A well known rear end shop is suggesting that I need a 9inch to take that power. In pics the 9inch looks pretty big and would think that the rear seat/floor area will need panelling out which I don't mind as I would have to make room for the third link anyway.
Is anyone using this axle in their MG? Do I really need it? I see a light weight housing and aluminium gear case is available to help keep the weight down.

Mark
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 17, 2014, 01:05:59 PM
Mark, You are in England, what's available over there? In America I would recommend either the Jeep Dana 44 (perfect width) or 90-92 Ford Ranger 8.8.(Needs 1 side shortened) On the Ford I would also replace the crush washer with solid spacer and eliminate C clips by shortening axles 1" and using small 9" ends. I don't know if they are available over there.
Title: Re: Which rear end for 400bhp MGB
Post by: DiDueColpi on January 17, 2014, 01:26:20 PM
My vote for the 9" is a huge "no".
It's a gigantic, heavy, power consuming monster.
It's only real claim to fame is that the neanderthals can't break it.
If you put one in you can never say the word "handling" again.
And say goodbye to 25 of your hard earned 450 hp.
Most R&Ps 8" or bigger can handle roughly 400ftlbs of torque.
(Torque is the yardstick that you need to use)
In such a light car as the MG getting that much power to the ground is a real challenge.
So an 8" is a realistic choice as long as a limited slip is installed.
Having said that.
I would probably lean towards a GM 8.5" rear end with a limited slip.
Just to have a little margin for error (drag racing).
Lots of choice (S10, Blazer, rear wheel sedans etc.) and lots of gear ratios available.
Some came with disc brakes as well.
Hope that helps.
Cheers
Fred
Title: Re: Which rear end for 400bhp MGB
Post by: Moderator on January 17, 2014, 01:44:13 PM
Are you willing and able to consider purpose built racing axles, like this one? http://www.1speedway.com/ministock_qc.htm

(http://www.1speedway.com/Images/Quick%20Changes/8100-c-1.jpg)

One can be seen in Phil's MG <a href="http://www.britishracecar.com/PhilLeonard-MG-RV8.htm">here</a>.

(http://www.britishracecar.com/PhilLeonard-MG-RV8/PhilLeonard-MG-RV8-DR.jpg)
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 17, 2014, 02:17:05 PM
Thanks for your replies.
The only axle that I can think of over here is the Atlas which is ridiculously expensive and not a lot stronger than what I have now.
I was originally planning on a Currie 8" with ally gear case but they advised against it as not strong enough.
Love the racing axle but not much helpful info on their site, but have emailed them for more info.
Maybe an 8.8 ford is the way to go but would prefer one from a mustang rather than an explorer as the tube size is smaller.
Can only find one mustang axle for sale over here from an 84 car listed at £800 or $1300+. That's a lot for a worn out axle that needs chopping.
Which are the best rear end companies. tried Moser but didn't get a reply, Currie enterprises want to sell me a 9 inch.
Need to get this sorted

Thanks
mark
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 17, 2014, 02:56:34 PM
That 8.8 is also big and heavy. Several considerations:
-Strength is dependent on ring gear size. OEM MGB is 7-7/8", good for about 300hp/300tq max.
-An 8-1/2" is good for 500/500. (You don't need 8.8 or 9")
-As ring size goes up, weight and bulk increase exponentially.
-A Salisbury type is always going to be heavier than a Banjo type. Alloy hogsheads are available for many Banjos. Banjo housings should be internally gusseted if used near their limits.

The ideal solution? An internally gusseted 8-3/8 to 8-1/2" banjo axle with an alloy hogshead that used a shallow helix angle for greater efficiency. (Both the 8 and 9" ford axles use a deep helix angle and give up about 5% efficiency). But I don't know who made one. I don't doubt that it exists. There may be one in a European or Japanese car or truck. In metric that would be a 215 mm ring gear.

In terms of a Salisbury axle, the Dana44 is probably the best choice, followed closely by the 10 bolt Chevy. Both had an 8-1/2" ring gear, both are very suitable in terms of strength, weight, bulk, availability and price plus availability and price of components, gear sets, and carriers (posi).

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 17, 2014, 04:14:52 PM
8 3/4" Mopar banjo is the best, but don't know if you can find one in England.

http://www.moserengineering.com/complete-rear-end-assemblies/875s-housing-axle-package-inch-part-number.html

http://www.moparmusclemagazine.com/techarticles/drivetrain/mopp_1103_rebuilding_an_8_3_4/
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 17, 2014, 09:51:24 PM
Mark, After some research, the Land Rover series III and V8 up to 2003 have the Salisbury(Dana 44). The 90 has a 4 pinion clutch type posi like the American Power-Lock. Same inner parts as Jag. Axles are offset and you may luck out and only have to narrow one side with another short axle. You want the one with the 640mm short axle.  You will have to redrill wheel lug pattern. 95-2002 have 3.54 gear ratios in coil sprung vehicles, I don't know what others  are available but Jag and Dana 44 will swap with the right bolts or tubing spacers. Will have to look at the rear axles stateside for MGB's. May be different. Look for this rear cover shape:
T2eC16JHJH0FG0-d14TBSVB0r0TYw60_58.jpg
_12.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 18, 2014, 08:09:38 AM
Thankls all,
This is so difficult as I don't want to make a mistake in choosing which way to go.
I like the look of the speedway rear end but they haven't replied to my email yet so hopefully will hear soon.
Really would have liked the ford 8inch with ally gearcase but is it strong enough?
The car is used mainly for track days so no hard launches and will never see the drag strip.
The land rover rear end looks interesting but am concerned about parts inter changeabilty. Really need a 3.25:1 or higher ratio,

Mark
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 18, 2014, 09:54:48 AM
Hmm, wonder what that Land Rover rear weighs.  Looks heavy.   The 8 3/4 MOPAR is my fav for hodrods, but they are getting hard to find. Used to be plentiful & cheap.
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 18, 2014, 12:22:10 PM
I wonder what the weight of the Mopar 8-3/4" is compared to the Dana44 or the Chevy 10 bolt. Neither will be as light as an 8" Ford of course but will be more efficient. The 8" has much stronger axles and spider gears than the MG axle but the ring and pinion is no better. Many have used them in higher horsepower applications but it is taking a chance, and in any event internal reinforcements of the hogshead flange would be absolutely essential in your application. Drag racers flogging the identically designed 9" found that flexing under hard launches changed the backlash causing greatly accelerated wear to the point where sometimes a set of gears would be shot after a dozen passes. That's 2-1/2 miles of hard use. Of course YMMV.

During the era that the MGB was manufactured, especially the Mark I and the MGA as well, it is reasonable to think that a larger sedan, perhaps some contemporary of Jaguar who was using the Dana hogshead but in the size you are looking for, might have used a larger version of the early MGB banjo axle. It is highly unlikely that any British car of the era used something like the 9" Ford, Dana 60 or 12" Chevy axle other than in a truck application but very reasonable to think they would use something a little heavier than the MGB used. What axle was in the Rover 3500 for instance? Wasn't that a Dana 44? Finding who manufactured the MGB Banjo axle would be a good first step. (Original application was a lorry? Or was that just the Salisbury?) Once you know who made it, finding what larger sizes they made and what vehicles they were used in should not be very difficult, especially if the company is still around. You could contact them directly. The design of that axle was really quite good, just what we are looking for in fact. An excellent balance of weight and strength and they are still very popular in racing even today. There is little doubt that the handling and ride of the car suffered with the upgrade to the Salisbury.

But one of the heavier/somewhat more powerful cars of the 50's/60's is bound to have this axle. And there are still a few old timers around who will remember it. Go up a class or two in racing cars and doubtless you will run across it. Very likely it is still to be found on the historic racing circuit.

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: NCtim on January 18, 2014, 02:11:02 PM
Why not a Jag E-Type rear end. I hear they're amazingly easy to fit on the MGB.

Tim
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 18, 2014, 03:31:04 PM
Tim
I have spent many years trying to get the handling as good as possible. I think the E type rear end will be way too heavy and im not convinced that the handling would suffer.
this is how my car goes,

 http://www.youtube.com/watch?v=tEmk_GkKWsI&list=UUX21gkuaDzTHCDE5vkwIEuQ&feature=c4-overview

I want to keep the nimble handling characteristics. I have seen many Jag rear end conversions but never one that performs on track.

Jim
There are not many large powerful cars over here with a live axle. The SD1 isn't much stronger than the B axle looking at the shaft diameters.

Cheers

mark
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 18, 2014, 07:30:05 PM
Yeehaw, that some great driving!
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 20, 2014, 11:14:02 AM
>Why not a Jag E-Type rear end.

Because unless you fully flare the fenders to an extra 3" per side you cannot get the uprights and knuckles outboard of the frame rails. If you do not get the knuckles outboard of the frame rails you either reduce suspension travel, increase ride height or both, and if you do that the car will not handle any better or even as well as with a solid axle, though the ride may be a little better in some ways. Plus, you add weight and though it is sprung weight, if you do not need it to counterbalance a heavier, more powerful engine up front it shifts the car's CG rearward, away from the ideal balance it originally has.

Now, if you *do* flare the fenders out a full 3" per side, you can run up to 315 rubber on the rear and have up to a full 8" of rear suspension travel, the results being much better road holding with a more compliant suspension (MUCH better ride), a wider stance for flatter cornering, and more grip for acceleration. Plus you can accommodate another hundred pounds in the engine compartment and keep the weight balance in check. But you can't do that with the E-type suspension, it is too narrow. Use XJ-6.

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: DiDueColpi on January 20, 2014, 01:17:11 PM
I'm still "all in" for an 8" rear end.
Particularly for a track car.
Unsprung weight is the concern here and the 8" is the lightest reasonable option.
It isn't going to be indestructible like a larger diff. But it will handle better. And it will live a long happy life if maintained well.
Have the axle tubes bent at the carrier end to give you some positive camber and away you go.
Cheers
Fred
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 21, 2014, 09:47:58 AM
Yes I really like the look of the 8"!  The drive shafts are 28 spline so stronger than the MG 21 spline shafts.
The weakness with the MG axle is the shafts but the diff itself holds up well. Is the 8" diff as strong as the MG axle?

Just taken out my half shafts and yes there are signs that the splines are starting to twist.

Its a shame that speedway didn't bother to get back to me.

Mark
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 21, 2014, 02:05:50 PM
The MG axle is weak in the shafts and the spider gears. About the same as the Ford 8" in the ring & pinion. But I personally have destroyed a stock MG R&P with a blown 215 and would be hesitant to push either it or the 8" much beyond 300/300.

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 21, 2014, 03:45:40 PM
From allfordmustangs.com


QuoteThe 8-inch rear end came out in 1962 [1962-1980]. The 8-inch 3rd members from '62-'66 are the weakest versions. Starting in '67-up, the 8-inch 3rd member case was revised [C7OW casting] to include more vertical and cross-webbing on the face of the case to strengthen it.

There are claims of people running these 8-inch rears with 400 hp, and they may be getting away with it, but these rear ends were not engineered to reliably handle that much power and torque --at least not without a lot of beefing up with [expensive] aftermarket parts.

All early V-8 Mustangs came with 8-inch rears except for the HiPo 289s --they came with 9-inch rears. The HiPo 289s were rated at 271 hp [Shelby 289s were rated at 306 hp].

The HiPo 289 carried over into the '67 model Mustangs. Even though the 8-inch 3rd member case had been revised by '67, Ford still did not use the revised 8-inch in the HiPo 289 Mustangs --they used the 9-inch.

Manual transmissions and sticky tires with lots of traction are not the only things that will kill an 8-inch. Most Mustangs suffer from wheel-hop, and this can also kill an 8-inch, even with regular street tires.

There are a few common failure points for an 8-inch; one is in the area of the input driving pinion support on the front of the 3rd member casting. The other is in the area of the pinion [spider] gears inside the differential, or with the differential main caps/bolts.

An example of a driving pinion support failure on an 8-inch [revised case] 3rd member:

http://img387.imageshack.us/img387/7...dmemberrq7.jpg


An example of the main caps and main cap bolts breaking that lead to this disaster on this 8-inch [revised case] 3rd member:

1. http://img387.imageshack.us/img387/2...n8inchclq1.jpg

2. http://img383.imageshack.us/img383/6...n8inchaas3.jpg

3. http://img362.imageshack.us/img362/6...en8inchru7.jpg

4. http://img387.imageshack.us/img387/1...n8inchbvn9.jpg

I suspect the reason why so many people run 8-inch rears, in applications it wasn't really designed to reliably handle, is because a [wrecking yard] 8-inch is much easier to find in the right width for an early Mustang than a 9-inch of like parameters. It's your car and your money, so only you can make the decision of running a rear end that might last, or to run one that will give you no worries.

An 8-inch, beefed up with expensive aftermarket parts, is only as strong as your base-model, stock-configured, run-of-the-mill wrecking yard 9-inch rear.

8-inch rear ends only came with differentials that had 2 pinion gears inside. A 9-inch could have either a 2-pinion differential, or a much stronger 4-pinion differential to distribute the force over a greater surface area.


From forums.mustangandfords.com


QuoteMy point though the article didn't address any of the issues with an 8 inch. People give up on it so quickly. There is a way to help the 8" fix the pinion spitting issue. (1 of the 4 main ways an 8 inch dies). By tapping the 5 pinion support bolts further down (by about 5/8"), longer grade 8 bolts, adding a Currie enterprises heavy duty pinion support and extra large bearing that goes with it helps that issue. I haven't heard any pinions being spit out after that upgrade.

With aftermarket axles and tapping the main cap bolts further (down to 2.5 - 3 inches) and even upgrading to 1/2 bolts using caps from Currie, you really raise the strength of the 8 inch to something that fixes the other 2 main reasons why an 8 inch goes. Main cap spread and axle spline twisting. Getting a closed diff also helps spread that torque over the axles as well, help the twist issue.

Get the wheel hop out of the rear end suspension and your pinion teeth will probably become less of an issue.

What you cant fix is the inner pinion support without going to either a Currie Alumin8 or up to a 9 inch rear. From what I have seen, once you upgrade to a better pinion support on the front, the inner pinion support becomes less of an issue.

BTW I have built my 8" this way. Currie heavy duty pinion support, heavy duty pinion support bearings, 4.11 gears (not Richmond though), tapped pinion support and main cap bolts.


Ford 8" & 9" spotter's info:

http://www.kevinstang.com/Ninecase.htm
Title: Re: Which rear end for 400bhp MGB
Post by: ex-tyke on January 21, 2014, 05:28:06 PM
Thanks Carl......this reinforces the fact that my choice of the 8.8 Ford wasn't flawed.
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 21, 2014, 06:11:55 PM
Graham,

The 8.8 is more than strong enough for most of us. Cause it's Ford's version of the the good ol' 12 Bolt Chevy! The axles are weaker than the 12 Bolt, though.  I have a 12 Bolt in my Camaro - Don't need no stinkin' 9 Inch!

If I remember you trimmed a good bit of weight from yours to make it a bit more acceptable.  I still believe with upgrades the 8 Inch would be fine to 400-450HP for non-slicks & no 5000rpm launches, Should hold up for road racing.

Here's an 8.8 article for ya:

http://www.carcraft.com/techarticles/116_ford_8_8_rear_end/viewall.html
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 21, 2014, 08:19:14 PM
Carl, Uh, I think I'm having Deja Vu! The 8.8 article emphasizes what I've been preaching for  years. Get rid of C clips, use 9"ends and solid pinion spacer. The stock  8.8 and 7.5 use the same 28 spline axle and bearings. The only difference is ring gear and spider gear size. The 90-92 Ranger with 4.0 V6 has the narrowest  offset axle 8.8 where you only shorten one tube. You cut 1/2" off splined ends to eliminate the C clips and shorten both sides further. Use the Moser small 9" ends for 8.8 (same as 8" bearing). That way you can convert to Mustang disk brakes.  Turn axle down .020 on bearing surface. Press on 9" bearing and retainer. Same width as MGB axle  and much stronger. Or even make shorter, like a 7.5 in a Spridget using cut to fit 8" axles,same 28 spline as 7.5 and 8.8.    
http://www.yukongear.com/ProductDetails.aspx?ProdID=1271
 The Explorer axle and some High Performance Mustangs had the 31 spline axles but are much wider. Uh Oh, he may be reading this thread for his next article! Just kidding, great minds think alike.LOL
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 22, 2014, 06:41:15 AM
Thanks, That  is a lot of interesting information.
Looks like the 8.8 is favourite. Shame there are not more of them over here.

I have ordered some coil overs today and will rig everything up using an old mg axle until I am happy with ride height and spring rate etc. Then I will have all the measurements for the new axle.

All these axle companies must be really busy because it is really difficult to get a reply from most.

Mark
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 22, 2014, 10:59:02 AM
Don't the battery boxes have to be cut to use the 8.8?

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: Moderator on January 22, 2014, 11:42:37 AM
No.
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 22, 2014, 05:22:34 PM
Good to know. I would have had to cut the boxes to use the Ford IRS with the 8.8, but I guess that was because of the mounting lugs.

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: kstevusa on January 22, 2014, 05:35:16 PM
I had to notch the webbing on my 8.8 to clear the battery box.  possibly weakened it a "TAD" but do not get enough traction to cause a breakage  problem.  
SAFETY FASTER!
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 23, 2014, 10:18:06 AM
Latest thought is to fit a gripper LSD to the existing mg housing with provision for 28 spline shafts. Have new 9" ends welded to my tubes.
This would be the easiest option and I could also get good money for the quaife that I take out.
28 spline axles look a fair bit bigger than the Mg 21 splines.

Good plan?
Title: Re: Which rear end for 400bhp MGB
Post by: BlownMGB-V8 on January 23, 2014, 06:14:58 PM
That should just about take care of the weak shafts and spiders. It'll hold up for awhile that way but with 400 hp you might want to keep at lease one spare around for when you need, it as you almost certainly will.

Jim
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 23, 2014, 08:23:18 PM
Mark, another weak point on the stock rear is the pinion crush sleeve. Should do a solid spacer and shims. I don't know what a Gripper is but I thought of a Aussie(Lokka) Locker for the 7.5  or 8"with the MGB cross pin. $250 with free shipping. Are you using the MGC ring gear?

http://lokka.com/site/home

http://fordmuscle.com/archives/2004/03/powertrax/index.php
Title: Re: Which rear end for 400bhp MGB
Post by: Scott Costanzo on January 23, 2014, 10:37:46 PM
This is a great thread. I was seriously looking at a Ford 7.5" as a future upgrade but the 8.8" with 28 spline axles is probably the way to go. I was under the impression that the 8.8" was a really heavy rear end but it seems that the Explorer 8.8" with the 31 spline axles, and disc brakes weighs about 175 lbs. compared to about 160 lbs. for the stock axle. I would imagine that the 28 spline unit cut down for a B wouldn't be too far away from a stock rear end weight wise. According to info in the archives here the Dana 44 weighs about 190 lbs. I know this probably doesn't do much for Mark's situation across the pond but it was helpful for me.
Title: Re: Which rear end for 400bhp MGB
Post by: MG four six eight on January 24, 2014, 01:59:14 AM
The Mopar 8 3/4" is plenty stout and with a Mopar Performance aluminum housing and Wilwood disc brakes I was able to get the weight down to around 160lbs if I remember correctly.

Pros,
Many came with limited slip.
Fairly easy to narrow and Moser has custom length axles.
Fairly light for how strong they are.
Aluminum housing saves about 9 pounds.
Still easy to get re-build parts for.


Cons,
Some of the taller gear ratios are getting harder to find new. (3.23 is just about ideal in an MGB with a V8)
The aluminum housing is expensive (about $1000)

Nuetral,
The aluminum housing requires removing the driver's side battery box on chrome bumper cars.

Bill
Title: Re: Which rear end for 400bhp MGB
Post by: ex-tyke on January 24, 2014, 08:55:05 AM
My 8.8 started life in a '95 Mustang - I had to remove quite a bit of extraneous nodular housing bracketry that wasn't needed for the MG for weight savings......unfortunately I don't have a final weight.......Here's the final configuration.
4-Link-Rear2.jpg
4-Link-Rear-1.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 24, 2014, 10:02:48 AM
Final configuration?!  You don't run rear brakes, Graham?  ;)

Until I get ready to jump into the 300+HP pool, I think Jim Nichols' 7.5" Ford would do just fine for me.
Title: Re: Which rear end for 400bhp MGB
Post by: psmg on January 24, 2014, 11:54:55 AM
Carl, if I remember correctly, you always said "brakes are highly over-rated". Or was it " Brakes? Who needs Brakes?" Anyway, hope you're staying warm.
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on January 24, 2014, 03:16:27 PM
Started chopping the MG today. Removing the rear of the boot floor and all the metalwork above the axle . This will make the whole job of fitting the suspension links much easier. Still planning on the Mumford linkage but will probably use a 4 link system as I am not keen on welding a a bracket to the cast diff. Will post pics. Also Collected new coilover shocks today.

Mark
Title: Re: Which rear end for 400bhp MGB
Post by: britcars on January 24, 2014, 10:05:42 PM
{Final configuration?! You don't run rear brakes, Graham? ;)  Until I get ready to jump into the 300+HP pool, I think Jim Nichols' 7.5" Ford would do just fine for me.}

Agreed.......putting together a 7.5" right now. The stock 3.9 has had a low growl for the past four years but got a bit worse last summer.  Time to change it out.  Planning to keep the stock drums though.
Ford7.5.Narrow.jpg5Copy.jpg
Ford7.5.Narrow.jpg8Copy.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: rubbinisracin on January 27, 2014, 06:26:22 PM
I'm running a Ford 8 inch ( http://www.britishv8.org/MG/IvanCollins.htm )  because Les Gonda did ( http://www.britishracecar.com/LesGonda-MG-MGBGTV8.htm ).  Mine doesn't have the upgraded third member but I did install new gears and a limited slip and upgraded half shafts.  No problems yet, but I really don't have a lot of really hard track miles on it yet either.  But I'd bet Les Gonda does.  

And here's how to make yours like Gonda's if you have a little extra cash.

http://www.currieenterprises.com/cestore/8inford.aspx
Title: Re: Which rear end for 400bhp MGB
Post by: 74ls1tr6 on January 27, 2014, 07:42:44 PM
How about Ted Lathrops 8" with Auburn possi (sp) with 32 spline axles and spyder gears ($$$$)?.I upgraded to 32 spline axles. I figured as lite as these cars weigh. This is what Brenda's GT will have and I know her engine will put 400+ to the ground. My setup just came in today from Ted! Very well made and clean looking.


2014-01-2716.33.06.jpg


2014-01-2716.32.51.jpg


2014-01-2716.32.35.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: Moderator on January 27, 2014, 08:05:31 PM
Calvin, that's gorgeous!
Title: Re: Which rear end for 400bhp MGB
Post by: danmas on January 27, 2014, 08:18:13 PM
QuoteHow about Ted Lathrops 8" with Auburn possi (sp) with 32 spline axels and spyder gears ($$$$)?.

I have one of those. I'm only putting down less than 350HP, so I should be good to go.

That's good news, because you guys were starting to scare me.
Title: Re: Which rear end for 400bhp MGB
Post by: mowog1 on January 27, 2014, 09:44:28 PM
I also have a Lathrop Ford 8" with Auburn 3.27 posi.

Undercarriage6-4-11.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 27, 2014, 10:24:51 PM
32 spline? Typo?
Title: Re: Which rear end for 400bhp MGB
Post by: 74ls1tr6 on January 27, 2014, 10:30:47 PM
Carl said:

QuoteUntil I get ready to jump into the 300+HP pool, I think Jim Nichols' 7.5" Ford would do just fine for me.

In the Miata/Ls1,2,and 3 world they prefer to use the Ford 7.5" rear end. Again they said the car is light enough to use with the swaps. the 8" is to big for clearance issues in Miata applications. Just a thought!

Same issue with the R200's in the drifting cars, said to be good for 550lbs of torque. In that application it would be the stub axles are the week link.

Just my thoughts, a 3500lb car and up would be looking closer to the 8.8" or 9" ring and pinion, and the 400hp in front of them.

Of coarse I'm talking normal and spirited driving with no clutch dumping. We all can spin the tires with out cars fairly easy!
Title: Re: Which rear end for 400bhp MGB
Post by: 74ls1tr6 on January 27, 2014, 10:37:51 PM
Quote32 spline? Typo?

They are normally 28 spline axles. I was talking to Ted and asked him about 400+ torque with his 8", he said you can go with the 32 spline axles and gears. I said I'll go for the 32 splined axles and spider gears. I'm also running 3.54.1 because of 6 speed T56.
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 27, 2014, 11:27:43 PM
I think he meant 31 spline.  I wouldn't use the 28 spline, either.
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 28, 2014, 06:05:39 AM
The 8" is right between the 7.5 and  8.8 in strength. Calvin is right on the lighter car being traction limited anyway. Carl's 300HP limit or use the 7.5 for 4 cyl,V6 or 215/3.5 V8. The 8" is perfect for 300 to a little over 400HP. Actually Torque is a better number. That is what breaks things The 8.8 if built right, is right up there with the Dana 44 and 9", should be good for 500HP. The 31 spline axles are larger diameter and stronger. For racing, I think the Dana 44  or 8.8 would be the answer.
Title: Re: Which rear end for 400bhp MGB
Post by: 74ls1tr6 on January 28, 2014, 08:19:29 AM
You at right Carl 31 spline!
Title: Re: Which rear end for 400bhp MGB
Post by: TXS67BGT on January 28, 2014, 09:57:40 AM
just to add another option in the mix, and Jim Nichols I hope you chime in here, I bought a rearend from a wrecked 98 Camaro Z28, 3.43:1 with disks, Eaton posi, seemed at the time to be just what I wanted, during the rebuild bought new bearings, clutch disks everything I thought I would need. the bearings for a 7.5 did not fit, after digging around with the local Chevy Parts guy he showed me that it was a 7 5/8, only two ratios available, ordered the bearings for that and they fit. Local (Kent Washington at the time) rearend specialist did the cutting and welding said he had seen only one other 7 5/8, said the tube walls were thicker than the standard 7.5. now all this is from memory, thought at the time I was rather lucky to run across it, hope all I have said is correct, do know it had Aussie aluminum calipers. The shop I bought it from had it in a car they had been drag racing with, behind a 415HP LS1 and it held up fine behind an 4L60E trans.
REAREND001.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: MGBV8 on January 28, 2014, 10:41:31 AM
How many bolts holding on the cover, 9 or 10? Sounds like it could be an Australian 9 Bolt.

They are actually pretty stout. A friend of mine had a Third Gen Camaro with one. It survived his Paxton centrifugal blower equipped engine & a 5 speed.

Great info:

http://www.thirdgen.org/techboard/faq-board/239666-everything-i-know-about.html
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on January 28, 2014, 08:06:35 PM
Hey Jay, GM 10 bolts after about 89 or so went to 7.625 ring gear and 28 spline axles. If I remember correctly,even the rear cover and outer bearings were the same as the earlier 7.5. The Australian 9 bolt was used in higher performance Camaro/Firebird. That rear cover looks more like a Dana and no C clips, also 7.75 ring gear.  Another option for a narrow rear is the 89-92 GM S10 2WD. It is 54"wide and if you cut 1" off splined ends to eliminate C clips, narrow tubes and use Ford bearing ends comes out 52" same as stock MGB. 4.75" Chevy wheel lug pattern.
Title: Re: Which rear end for 400bhp MGB
Post by: TXS67BGT on January 29, 2014, 04:06:26 PM
counted, 10 bolt.
REAREND005.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: waterbucket on February 02, 2014, 02:31:32 PM
There is another axle available in the UK, the one from the Reliant Scimitar SE5. I think I am right in saying that it is only 11/2 inches wider than the original B axle, it has the brackets already for a four link location and a Watts linkage for lateral location. It takes Jaguar diffs (or Dana 44) so plenty of choice there for ratios and lsd. I guess it might be lighter than the Land Rover axle.
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on February 04, 2014, 07:01:46 AM
Thanks everyone.
looking at the photos some have mounted the shocks just in front and some just behind the axle. The ford escort coil over kits mount the shocks on top of the axle. Is this as a result of packaging or is there an optimum position. I have room to fit them on top of the axle or just in front. Which would be best?
Cheers
Mark
Title: Re: Which rear end for 400bhp MGB
Post by: Moderator on February 04, 2014, 10:29:55 AM
Putting the shocks in front of the axle leaves room for a Panhard rod or Watts linkage between the axle and fuel tank.
Title: Re: Which rear end for 400bhp MGB
Post by: TXS67BGT on February 08, 2014, 08:26:40 AM
for your reference, shocks behind the axle. used Bill Guzmans setup as the basis
REAREND081.jpg
REAREND067.jpg
Title: Re: Which rear end for 400bhp MGB
Post by: mgb260 on February 13, 2014, 10:00:47 PM
Jay, Nice looking setup. It'll be a smooth ride. Did you center or use aftermarket fuel tank? Curtis is right on front mount shocks/rear panhard , not a lot of room between the rear axle and tank . Triangulated like Jay and Graham have can be mounted either way. V8bloke(Mark) any progress pics?
Title: Re: Which rear end for 400bhp MGB
Post by: roverman on February 14, 2014, 12:09:21 PM
Mark, We are about "sharing", beneficial knowlegde-here.  How about you tell us all about your TA headed, RV8 build ?  You have not mentioned, if you will need different r & p ratios, for different circuits. If so,IMHO, you'll definately want a drop-out center section.Servicing a drop-out, on a bench, sure beats an "integral", in the car.  Are you drag racing or road racing ? Drag slicks and drag tuned suspension, will shock-load a chosen rear, to the max. There are items to counter-act this. 8" Fords have 31 spline axles available, even hollow , lightweight full floater set-ups. 4 spider limited slip units, including gear only.What will be the r & p ratio, as this affects strength. More teeth in contact + stronger.  Maybe a ring gear "thrust button", like 9 inchers use ? "Soft-lock" clutches, are available.  Perhaps a rubber coupled drive shaft ?  Good Luck, Now tell us, about your RV8.  roverman.
Title: Re: Which rear end for 400bhp MGB
Post by: v8bloke on February 15, 2014, 04:06:52 AM
Thanks guys,
modifications are progressing at a very slow pace. Will post pics soon. Rather than work around the existing metalwork I have chopped out everything between the chassis rails inc most of the boot floor up as far as the rear seat kick panel. I seem to spend a lot of time just looking at it with arms crossed trying to figure out the best way forward.
The brackets for the Mumford linkage are made and am waiting for billet ally bell cranks to be made.
I will be using an MGB axle with stronger shafts for now but have made sure there is room to swap to a larger rear end if needed.
At the moment I am making and welding on all the housing brackets for upper and lower trailing links, mumford links and anti roll bar. I am still not decided exactly where I will be mounting the coil overs but it is likely to be behind the axle as the mumford link brackets will double up for mounting them.
Also I am having an aluminium fuel cell made that will fit upright with a built in swirl pot and baffles.
Although the car is road legal it is mainly used for track days and is stripped out so I am not at all worried about originality.
Will post some pics soon.

Mark