I feel like i'm finally over the hump on mine... sent it out to a media blaster this past weekend -- hope to have it back next week. When i get it back, the next priorities are...
- a bit more welding to do on the bottom side -- stuff like adding in some bracing, welding the rear bump stops back on & a couple of miscellaneous other things
- finish welding in the cowl panel for the swap to a metal dash
- fit the Omni fender flares
Then lots more to do after that!
Here are a couple of progress pics...
2007-10-06MGFirewallOilCoolershelfmodsfromUnderneath003.jpg
2007-04-07DashBumperRadiatorSupports008.jpg
2006-12-09ACFittingInProgress005.jpg
2007-10-14MGonRotisserie001.jpg
Although I'm not doing the work myself, work is proceeding rapidly on mine. Progress pictures at: http://www.advanceautowire.com/mgbgtv8
Dan, i do love looking at Ted/Don's work!
It looks like your motor sits even lower than mine based on how much room there appears to be over the throttle body -- especially given that the intake is an air gap one... is that an illusion or did Ted change the motor mount design from the way he used to do it?
Well Winter will be here before we know it and I believe the Last good days to take a spin are gone..I have been getting my list together of the things that I want and need to get done on mine during the snowy months.
The Drive line will come out and the engine rebuilt with added "Go Faster Parts ".
The engine bay will receive a much needed overhaul and new paint.
The headers will get Jet Coated or something similar and of coarse the interior could use some attention, Door panels and Maybe some Fiero seats.
And last, finish my rollbar so I can go Faster at the drag strip.
So as you see even though I was able to drive mine this past Summer it is far from done.
Joe
Yeah, mine too. I found one tire for it, when I change that I'll re-seal the rim halves, and I have a different set of springs to go under the car. Then if I can get a set of cylinders for the tilt front end that'll be enough for this winter.
Jim
Rob,
I'm not sure what Ted's mounts were before, but he has gotten the engine low enough in mine that no hood bubble is needed - the hood will close over the engine.
I've posted some new pics on my web site.
I am putting together a V6 for my son and am at the point of installing a radiator now (early Mustang V8 radiator for a standard 60V6 implant). I was a bit worried at how much of it hangs down in harms' way. Thanks for posting that picture Rob. I looked at other installations in the photo gallery and most non-MG radiators were sitting below the steering tie rods. The RB MG radiator is about even with the tie rods.
Hmmm Dan's pics also show the radiator sitting lower than the RB MG radiator (looking good Dan).
Still kind of spooky though.
I think so too, in fact the first extended radiator I used hit a curb. But it isn't that hard to place a guard below the radiator.
Jim
Hey, thought i'd post after lurking for a while.
Just nearing completion on mine, it's a 78' roadster or a massive hole in my wallet however you want to look at it...
Basically it's a sound original car (45k miles and garaged from new) with no rust at all, I've fitted a complete new interior, inc new leather seats, carpets, roll bar, all the usual bits. Fitted gas shocks all round, lowered V8 springs, cross drilled and grooved V8 discs, kevlar pads, all new rear brakes. The engine is a Rover/Buick 215, stripped, acid dipped, rebored +20thou, rover vitesse 9.75:1 pistons, fast road cam, skimmed and ported heads, remote oil filter + cooler, new V8 larger core rad, stainless steel block huggers with full stainless system, new rover LT77 5 speed with custom prop, edelbrock 500 on the offey dual port intake, + few nice shiny bits. It's running on recon Triumph stag wheels (similar to LE) with V8 chin spoiler.
Just finishing the last parts off now with the cooling system, anybody got any bright ideas on the heater control valve?
I'll post some pics of the build soon if anybody's interested?
Paul
QuoteI'll post some pics of the build soon if anybody's interested?
I'm VERY interested!
The message board is a cool place to post photos... but you're also invited and encouraged to submit a "How It Was Done" write-up for our online newsletter and photo gallery.
This link includes tips for submitting photos and also explains our tried-and-true "How It Was Done" article format: http://www.britishv8.org/British-V8-How-To-Contribute.htm
Curtis
My Rad support both protects the low hanging rad but also serves as a jack point, Very handy.
Joe
QuoteMy Rad support both protects the low hanging rad but also serves as a jack point, Very handy.
Indeed... as shown here (in Joe's HIWD): http://www.britishv8.org/MG/JoeSchafer.htm
Brent Lancaster took a somewhat similar approach: http://www.britishv8.org/MG/BrentLancaster.htm
I'm planning to do something similar when i make the shrouding for the part of the radiator that hangs below the oil cooler shelf. I didn't have the special tuning air dam when i started setting up the radiator, but got it (along with some other goodies) from Bill Guzman recently [thanks again Bill!]. When the body shell gets back from the stripper (later this week i'm hoping), that's one of the projects I have to complete. What I'm thinking is a frame similar to what Joe did but with shrouding that leads to the air dam opening so the fan sucks air from in front of the car rather than hot air from under the car back around through the radiator.
On mine I built a forward crossmember structure of thinwall materials which is a radiator guard, jacking point, center section of the spoiler, forward radiator shroud, and anchor point for the tilt assembly pivots. Very happy with the results.
Jim
I have just send my GT which is ready for respray, off to storage, sigh, but that means the V8 can go into the garage to be finished ready for next years shipping to the USA.
I have fitted a "new" LT77 box but have found out that the linkage is shot so I am waiting for new bushes. I can then refit the engine, then the exhaust, then I can finish the rear valence exhaust cutouts, so then I can get the baby resprayed!!!
A few hours ahead of me I think.
Dave
looks like everyone is upgrading or putting a serious effort fwd to make it to Elkhart Lake next year! thanks Rob for the TL, it matches perfect. WTG, Joe looks like you have the BUG!. what mods do you plan. send me a PM on your combo, and we can wish any level of performance. i have my new SP gas tank mod completed and still lack cutting the trunk (boot) floor for mounting. i took pics and have most of the info should anyone need suggestions. the GM Fuel Module fit perfect into the GM Flange we SOLDERED to the SP tank. the coating applied by SP was not damaged by excess heat of welding. i plan to do a " How To" article for Curtis when i have recovered from a brief proceedure. look fwd to seeing you all again at next "conversion meet" Hell, i think Bill G. has converted me to a V6 fan also. would have saved much $ and room, but strokers don't come cheap!
SAFETY FASTER!
Kelly
All the best with your mentioned procedure!
Nothing against the V-6s However I think you would have to spend big$$$ to get a V-6 to run as hard as your 5.0
Glad to here on the fuel tank I will be checking it out. As far as my mods that is still in the air, maybe a little maybe a lot:)
Joe
"The Proceedure" was a success. Got a brand new Bio-Met Mangnum right hip. 3 days and home again. can't do much but dream. just need to be able to get the old tank off and measure for the cut and do the conversion. the GM module fits great. will use 4AN & 6AN SS Braided slip on to connect to the hard lines and module lines. 4AN will slip onto 5/16" and 6AN will do the 3/8" on the module. i will slip a piece of 5/16 into the 3/8 " line and silver solder for my existing lines conversion. (both are 5/16") just have to drop down from the 3/8 on module to my 5/16" for short distance.
Rob seems to be speeding toward completion and hope to see him in Wisc. all you guys keep the flame going. Hot Rodders forever! just a different car, seems like the true spirit of our forerunners.
just think, i can be down 4 cylinders and still put out 37 HP per cyl. or 148HP for 4 cyl. the Super charged 4 cyl maxed out! and i only spent a few dollars more and have to hook up 4 plug wires to double my HP. Wow! could never be happy with the anchor again.
FOR CARL-- SAFETY FASTER!
kstevusa Wrote:
-------------------------------------------------------
> Got a brand new Bio-Met Mangnum right hip.
Must have wore out the original from too much standing on the loud pedal !! ;)
Did you go to the Chattanooga Choo-Choo ? Jim Watson from the Blount club (Knoxville club that does the Townsend show) Said that there were 3 V8s in attendance. Mike Cook with his Silver Lady, Chris Gore with the Red Pearl, and ? I though it might be you since you are nearby.
Hope your recovery is going well. You should be ready to go for a run with me by the V8 Meet. :)
Doing some minor stuff on mine. Finally put a heater in it. One of those compact units from southern rods. Works pretty good, about the same amount of heat as the OEM unit. Enough to keep the better half happy! Some changes to the coolant tank, to allow installation of the heater.
Also switched to 19lb injectors, from the 21lb units.
Carl, hope to attend the event in Elkhart Lake, but will fly. No, i did not make the SBCC event in Chat. it was over before i knew it was happening. you bet i will try to do better on the auto-cross. i had a senior moment on path thru the cones and could not visualize the correct path. best way is to ride with someone and get the proper path. even better, just line it with chalk or other medium and maybe i can follow it. guess i just prefer the straight line. thanks for "Well Wishes" and everyone have a safe and happy Holiday Season.
SAFETY FASTER!
I pretty well have my 74.5 MGB Roadster dismantled in preparation for the addition of Omni flares this coming February.
I have pretty well decided on the wheels and tires and I am currently pricing them. In the interim period I will be taking a new/used fender and a hood back to bare metal. The fiberglass bumpers have to be tweaked a bit. New kick panel to be made up, some electrical modification.
I am considering shaving the door handles and locks and will have to research how a remote opener works.
so there is lots to do.
Bruce
I have been playing hooky from clients cars for a few days to put together my 1980. I have been putting this off for the last 3 years+++. I do have a writeup on why my own car has never been done, but I think its the same reason as everyone else's. Was hoping to have the BGT V6 ready to go as well, but Rick is gone so chances are good that we will only have one B of our own there... If all goes according to plan. Still need to rent rooms though.
My brother would like to attend with his repowered Porsche (German car= he is the black sheep of the family!), would there be room at the event for his car to run the track and whatnot? Whos arm needs twisting to allow him to drive his car to this? ;-)
-BMC.
Mine is my garage getting a new rear end and a hood cowl made. As well a little carb work ans clutch inspection.
Carl,
The other car at Chatanooga was Chris Powell. He has a 78 B with hardtop and chrome bumbers installed. Engine is a 3.9 Rover and a Camaro v8 trans. Ford rear with 3.55 gears and posi. Run very well. It is also has AC.
I picked up a 290 hp Chevy crate engine for $1500 dollars at a Charlotte, NC car show. It will go in my 85 Jag XJ6. The car Carl saw in Tenn.
I hope to get in installed by the end on Jan, 2008.
I am also finishing up a Ford 8 in for my V6 MGBGT. Alonger gear should help on the open road. That should be done in Feb,2008.
Hope to make the V8 meet in Wisconsin. Haven't decided which car th take though.
Steve
I hope to get the C axle and C exhaust under my car this year and redrill the leaf spring mounts at the same time, both front and rear. Also want to get the CB crossmember installed. Easy to say, hard to find the time and motivation to do it, even harder to get them synchronized.
Hi All,
My project is going slowly, and its kind of OK. I'm not the wrench turner on it, no skill. Its being done at a shop in Windsor, Ont. by a guy that has one LBC conversion previously done. I want to thank Kelly, Joe, and Graham for the help and guidence they gave me at the 2007 meeting in Ohio, and in Michigan. We are at the second engine fit stage and getting to the building of the headers point in the project. There's a lot of thinking, and not much doing at this time but that may save money and time in the long run. We will be doing a front shock conversion, I got a kit with a pair of Spax shocks and it looks neat. We will also be trying a Strange front steering rack(borrowing one to try out before we buy). The rear will be a 8.8 from a Lincoln with disc brakes and posi, probably 3.55 or 3.43. The engine is a stock 302 from an 88 Cougar, a tremec 5 speed is already attached. The plan includes keeping the rad, front brakes, and heater, and putting through the inner fender headers on with a fuel cell type gas tank that will create a new trunk floor(old one has the only rust on the car). I'm planning to keep the fenders un-welled, but I'm not married to having a stock only look. The front hood will close with no holes in it. One of the questions I have is what type and size wheel should I look for? I'd like to go with a 16in 215 or 225 but I don't know if it will fit. My budget for this project is limited and I'm trying to save where I can and not where I shouldn't. I just got a 70 BGT that is crying for a V6, but I can only handle one at a time unless something hits me between the eyes and I have to go for it. I'll try to attach some photos but I haven't been too successful at that. I'd appreciate any suggestions anyone has about any of our decisions.
Thanks,
Marc
Welcome to the forum Marc!
I see that your problems validating your new UserID are all settled. I've sent you a "personal message" so you can see how that works too... and in it I've included instructions for posting images. Just look in the upper righthand corner of the screen and where it says in RED "You've got a new personal message" (or something like that)... well... just click on that. (If your e-mail program is accepting our system's automatic e-mails, you should also get a personal message notification by e-mail.) There are some tips about using the message board in the "test messages" forum. When in doubt, just "click" on stuff!
Sounds like your car is off to a great start! I'll shut up now, and hopefully someone else will chime in.
Marc, I can't help but think of a fellow Canadian with a 302 powered B that has some wheels and tires that are probably about what you had in mind. Check out Dennis McIntyre's car. http://www.britishv8.org/MG/DennisMcIntyre.htm He's running some 205 17s that look pretty good and fill the wheel wells nicely. As Curtis said, welcome to the Forum.
Thanks for the suggestion, the wheels don't look too big to me. I will have to make a decision soon on a bolt pattern, because the Lincoln is a 5 bolt. I will probably change the fronts to 5 bolt, but I need to be sure because the wheels and tires will be the second biggest outlay of cash, for parts, after the motor and trans. The other project I'd like some info on is my 70 BGT, that I would like to put a V6 into. Has anyone used a Buick regal 3.8 supercharged(FWD) motor for a swap? Is the 4.3 vortec a viable candidate? The little GT would go great with some more torque and HP. My pics are too big to get on the site. I have to find a way to make them smaller.
Marc
I hope these pics come out.
Marc
IMG_0520.jpg
IMG_0517.jpg
IMG_0522.jpg