The Ford V8 kit is now completed and ready to ship.
This kit is a bolt on and is also adjustable. All parts are powder coated.
Kit fits the CB and RB. All modifications to install the Ford V8 apply.
Kit includes the following:
Trans cross member
Frame brackets
engine brackets
motor mounts
bolts and instructions
No headers.
Hey Bill -- this post is only a tease w/o the pics!
And a price!
This forum does not allow me to post pictures. The price is $355.
You can see the pictures in MGexperience forum
QuoteThis forum does not allow me to post pictures.
that's news to me! why doesn't it?
No nude models allowed, Bill! :)
I'm betting the pics are too large.
Yes to large?? 2048 X 1536
Per forum rules - no photos larger than 600KB.
Pretty well requires a free download pic resizer programme like 'PIXresizer'.....
http://pixresizer.en.softonic.com/
Graham, very IMPRESSIVE software
It's not really necessary to download a program for this. You can use a handy online tool like this one:
<a href="http://www.shrinkpictures.com/">ShrinkPictures.com</a>
---
Instructions:
Browse for your picture.
Where the ShrinkPictures tool says "Select New Maximum Image dimension", choose "600 Pixels".
Click "Resize"
Click "Download this picture Now"
Thank you Curtis.
phpo5zmmoAM.jpg
Sorry but Im a little ignorant when it comes to the short forms. I have a 1969 BGT will this kit work without a lot of additional mod. ? THANKS DAVE
I just use Microsoft Paint to resize my pictures
Paul
"Graham, very IMPRESSIVE software"
Merv: PIXresizer is great for single photos. If you want to re-size a batch of photos, I like Visualizer-Photo-Resizer.
Phil O
http://www.softpedia.com/get/Multimedia/Graphic/Graphic-Editors/Visualizer-Photo-Resize.shtml
Welcome to the forum, Dave!
CB = "chrome bumper" = up through 1974
RB = "rubber bumper" = from 1974.5 on
So yes, this kit is applicable to your 69 GT.
Bill,
How much fabrication is necessary to do along with this kit? Bolt in? The only fab work that I'd like to do is the holes for the exhaust.
***Graham, We spoke when I saw your car at the meet last summer, I'm in the Detroit area, I would like to get a better look at it when the weather warms if possible...I have a GT the wants to be like that when it grows up!!!
Mark
Mark, I'm sure we can work out a tire-kicking session somewhere near Motown - I'll be visiting Kayak Jack in Dearborn when top down weather gets here......will keep you informed.
Mark, the same fabrication is needed when installing a V8 in a an MGB.
The kit will facilitate the installation of the V8 since it is a bolt on kit all you need is to drill holes.
It also allows for pinion angle by just adjusting the motor mounts.
For headers Teds from Fast Cars will work. We will work on headers if it is enough interest.
Thanks Gentlemen...
Bill, I know I had talked to you about the V6 route, but I have all the main parts for the V8 swap just collecting dust. The only area of question at this point is will my TKO3550 fit without too much tunnel modifications? Any thoughts?
Mark
Hey you guys, when in the area stop by the shop,just give me a little warning 313-533-2457
Dave Craddock
QuoteHey you guys, when in the area stop by the shop, just give me a little warning ...
...and we can go to the TRACTION BAR for lunch!
Quite right mate,, and I'M buying !!!
Graham don't invite the whole club,,, eh.
just kidding
Dave
No mods needed to the tunnel
I like that Traction BAR
Hey, Mark, Graham, Dave and you, too, Bill if you can make the drive! :-) The Traction Bar is a good stop. Count me in! ! ! I got my 80 B 3.5L out of the garage today. I went for a long drive and it's running good. The garage temp was 43 degrees but I think that will be as low as it gets from now on. Hope to see you all soon! Let me know the day. Maybe I'll use the Ford setup in the 79 B.
43 !!!! that is my refrigerator temp.
Thanks for the help...and the help yet to come!
I've built cars before, but those have only involved upgrades. This will be my first car from scratch, it's intimidating. Making structural modifications, braking and cooling systems from scratch...not things that I've done before. That said, I want to go into this learning as much as I can and have a plan before I start. Cutting the body concerns me the most. I will probably have to lean on your collective knowledge often. Thanks in advance again!
Mark
43? that's the year I wuz born !!
Dave