BritishV8 Forum

General Category => MG Sports Cars => Topic started by: MARVIN, CT on April 05, 2011, 09:55:51 PM

Title: T5 transmission mount
Post by: MARVIN, CT on April 05, 2011, 09:55:51 PM
I'm nearing completion of putting a  Mustang t5 in my TD, behind the Ford 60hp. The t5 mount is at least twice as tall as I can use. Any recommendations for a mount about an inch or so tall. Thanks, Marvin
Title: Re: T5 transmission mount
Post by: rficalora on April 05, 2011, 10:00:21 PM
how about don't style engine mounts?
Title: Re: T5 transmission mount
Post by: Moderator on April 05, 2011, 10:09:02 PM
Donut?  Is that what you'd call this 2-piece style, like I used for both engine and transmission?

(http://www.barrycontrols.com/prodfiles/images/fam_img_45.gif)

You should be able to find them from all sorts of industrial supply outfits... McMaster-Carr, etc.
Title: Re: T5 transmission mount
Post by: rficalora on April 05, 2011, 11:21:57 PM
I was thinking of these types available from hotrod suppliers, but either would work.
donutmount.jpg
donutmount2.jpg
Title: Re: T5 transmission mount
Post by: ex-tyke on April 06, 2011, 09:40:52 AM
Anchor 2268  - T5 mount - used in early GM and Ford products
 
Anchor2268.jpg

I should add that O'Reillys have them for $4.99
http://www.oreillyauto.com/site/c/detail/ANH0/2268.oap?pt=03234&ppt=C0019
Title: Re: T5 transmission mount
Post by: mgb260 on April 06, 2011, 06:27:31 PM
Marvin,Just curious,did you use the S-10 tailshaft with the Mustang T5? Commonly done in street rod flathead T5 swaps.
Title: Re: T5 transmission mount
Post by: MARVIN, CT on April 06, 2011, 08:33:31 PM
Jim, I used the Mustang tailshaft, perfect position in the TD. I just need to bend the shift lever over to the right to center it, if that's possible. Marvin
DSC00007.JPG
Title: Re: T5 transmission mount
Post by: mgb260 on April 06, 2011, 10:08:33 PM
Thanks, Marvin! You never know,maybe I'll pick up a TD someday. I know a guy that goes to Brazil every so often. I asked him if he could round up some Ardun style Simca Hemi heads to fit the flathead 60. There are a couple running motors on U Tube. You should be able to bend the shifter in a large vice,may need to heat it.
Title: Re: T5 transmission mount
Post by: rficalora on April 06, 2011, 10:32:51 PM
Doesn't the shifter lever just bolt to a stub on the shifter itself?  If so, it might be easier to do what I did -- I welded a bolt to the top of a piece of 1" square tube -- drilled holes through.  It slides over the shifter stub & bolts on.  If I remember right the stub was a little smaller so I used some 16 or 18ga stock to make shims that I tacked inside the tube.  My shifter is a Steeda but I think that part of the design is the same as stock mustang shifter.  Was quick & easy & you can make the shifter any lenght you want that way too.
Title: Re: T5 transmission mount
Post by: mowog1 on April 06, 2011, 11:17:37 PM
Curious....what differential are you running in the TD?
Title: Re: T5 transmission mount
Post by: MARVIN, CT on April 07, 2011, 08:49:36 AM
It's a stock TD axle with MGB 3.9 gears. Marvin
Title: Re: T5 transmission mount
Post by: theonlyiceman53 on April 07, 2011, 09:58:42 AM
This is what I put together for the 4.3 Spitfire.  Might be about what you are looking for.
Bill

IMG_3133Trannymount.JPG
Title: Re: T5 transmission mount
Post by: deltadave on April 07, 2011, 02:54:11 PM
I bent the T5 Camaro shifter in my TD, but it took some heat to do it. Glad to see you got the system worked out. I'm painting the TDs wheels and will post the finished pics soon.
Title: Re: T5 transmission mount
Post by: J Man on April 07, 2011, 04:13:58 PM
Lokar makes a aftermarket shifter for the T5. It would give you a couple other options and they will be better looking.
Title: Re: T5 transmission mount
Post by: MARVIN, CT on April 08, 2011, 10:21:07 PM
The Mustang mount worked with a bit of adjusting. Thanks to all for the suggestions. Moving right along, Marvin
DSC00004.JPG
Title: Re: T5 transmission mount
Post by: MARVIN, CT on April 14, 2011, 08:41:43 PM
Well, I evened out the transmission mount with an ash wedge and straightened the gearshift lever with a bit of heat. Getting there, slow but sure. Thanks for all the suggestions, Marvin
DSC00016.JPG
Title: Re: T5 transmission mount
Post by: BillinCT on April 14, 2011, 09:30:10 PM
Good job on straightening the shifter, Marv.
Title: Re: T5 transmission mount
Post by: pspeaks on April 16, 2011, 09:40:33 AM
Question, what thread is the two shifter handle bolts, not 5/16"-18, I'm assuming metric?
Title: Re: T5 transmission mount
Post by: MARVIN, CT on April 16, 2011, 01:23:25 PM
Paul, I don't have a metric gage, but the bolt head uses a 10mm socket and the treads are 20tpi. Marvin
Title: Re: T5 transmission mount
Post by: pspeaks on April 16, 2011, 02:32:44 PM
Thanks Marvin, I just made a run to the hanger where the car is and checked it.  I don't know if they're all alike but mine is M8X1.25.

"P"
Title: Re: T5 transmission mount
Post by: Dudster on April 25, 2011, 02:39:24 PM
I'm looking for a mount for a Tremec T5 (Ford version) transmission that is similar to the Anchor 2268 pictured above.  The problem is that I need the base holes 5 1/2" apart instead of the 4" of the 2268.  The local parts stores are no help.  I can get one with bolts protruding downward but that would leave over an inch of bare threads under the car.  Any ideas.

Thanks,
Bill