BritishV8 Forum

General Category => MG Sports Cars => Topic started by: rficalora on February 12, 2011, 08:11:16 PM

Title: Did a short test drive today
Post by: rficalora on February 12, 2011, 08:11:16 PM
Put the car on the ground & did a short test drive today...  I knew brakes are too soft to drive much but it was fun anyway.

Did identify a few things to address
 -- need to raise the car up - exhaust scraped going out of the driveway
 -- leaking coolant -- I think it's coming from the bottom hose but I'll need to look closer to be sure
 -- need to adjust the shifter -- it's not fully engaging 1st & wants to pop back to neutral

But still - after several years it was great to have it on the ground & moving under it's own power.
2011-02-12MGbefore1stTestDrive5.jpg
2011-02-12MGbefore1stTestDrive9.jpg
Title: Re: Did a short test drive today
Post by: HealeyRick on February 12, 2011, 08:24:18 PM
Congrats, Rob.  Love the wheel and tire combo and looks great under the flares!
Title: Re: Did a short test drive today
Post by: MGBV8 on February 12, 2011, 08:48:59 PM
Damn that's purty, Rob!

"-- need to raise the car up - exhaust scraped going out of the driveway "

Fix the driveway. The car is perfect ( I never argue with perfect).
Title: Re: Did a short test drive today
Post by: mgb260 on February 12, 2011, 08:49:29 PM
Yeah, Looks great,Rob!
Title: Re: Did a short test drive today
Post by: flitner on February 12, 2011, 10:35:27 PM
Rob, I cant wait to be in your shoes!!! the car looks incredible and I bet it sounds great too!!!! Nice werk Cheers!!!!!!!!!!!!!!!!!!!
Title: Re: Did a short test drive today
Post by: BlownMGB-V8 on February 12, 2011, 10:51:05 PM
Looking good.

JB
Title: Re: Did a short test drive today
Post by: MGBV8 on February 12, 2011, 10:52:51 PM
Fix the F...in' driveway, nuthin' wrong with the car!  

My car is going lower than it was.
Title: Re: Did a short test drive today
Post by: kerbau53 on February 13, 2011, 02:31:05 AM
Great. Wheels really suit the car!
Title: Re: Did a short test drive today
Post by: kstevusa on February 13, 2011, 08:55:45 AM
Great Job!   Rob , look fwd to seeing you in Townsend.  Love the color
Title: Re: Did a short test drive today
Post by: castlesid on February 13, 2011, 08:59:36 AM
Rob,

Car looks fantastic, I'd try and avoid raising the rear end if at all possible, whats the distance from centre of wheel to the the bottom of where the chrome strip would have been, ideally for road use this should be approx 15" If your car was originally rubber bumper it would have been a lot higher.

If you still using leafs spring at the rear then you want no more than a 93lb spring rate and thebest steel springs are the Moss reverse spring eye springs which will lower a rubber bumper car by 1 1/2" - 2"

I have these springs on my GT rated 110lb and dont have clearance issues with the exhaust although my tail section is for a rubber bumpered car and it now rides at chrome ride height so it could be raised for more exhaust clearance.

Kevin.
Title: Re: Did a short test drive today
Post by: ex-tyke on February 13, 2011, 09:21:35 AM
Congratulations from North of the border.
Teething pains will always be part of a new conversion - you'll get them sorted quickly.
Title: Re: Did a short test drive today
Post by: Jim Stabe on February 13, 2011, 08:08:24 PM
Rob

Beautiful car! The stance is great, don't raise it up - I might even drop it another 1/2" in front. I looked through your journal and didn't see any pictures of how your exhaust is run but there are things you can do to gain some clearance. Could you post some pictures showing where you are having the clearance issue. I have my exhaust up inside the tunnel, not an option for you but I did have to clear a couple obstacles and I made some low profile ovalized sections to get underneath them. The 3" pipe flattens to 1 1/2" where it goes under the rear end and the        2 1/2" squashes down to 1 1/4" under the throw out fork on the bell housing without losing any cross section area (ie flow). If you are interested, I can show you how to make them - it's pretty easy.

I really like the mirrors also. Good mirrors that look good on our cars are really hard to find.

Exhaust010.jpg

Exhaust027.jpg

Exhaust025.jpg

Exhaust023.jpg
Title: Re: Did a short test drive today
Post by: Bruce Mills on February 13, 2011, 11:33:35 PM
Very nice Rob
Title: Re: Did a short test drive today
Post by: danmas on February 13, 2011, 11:57:29 PM
Rob,

Looking good!  I can't wait to see it in Townsend.
Title: Re: Did a short test drive today
Post by: rficalora on February 14, 2011, 11:37:15 AM
Jim, it scraped @ my H tube cross pipe.  I checked the car height & I am a little low.  Just shy of 14" front and 14.25 rear.  Raising to about 14.5 isn't likely to make enough of a difference so I may have to do something like you did.  Anyone ever measured a typical speed bump?  Unlikely I'll be able to clear one.
Title: Re: Did a short test drive today
Post by: Bill Young on February 14, 2011, 12:42:36 PM
Rob, my Midget is real low, especially right at the center where the catalytic converter is mounted so I scrape that often. I recently raised the car a bit and it's much more pleasant to drive as I'm not worrying about every bump in the road. I had some worrying moments on the trip to Durham because of road construction where the lanes were uneven and you had to transition over that edge in a few places. At 60 mph you tend to clinch up the backside when negotiating something like that. I didn't get much higher maybe an inch but it made a world of difference.
Title: Re: Did a short test drive today
Post by: Jim Stabe on February 14, 2011, 02:08:57 PM
Rob

I've has a couple questions about how I did the ovalized sections. I'll take some pictures and post a how-to on here in the next couple of days. You reduce the diameter of the pipe by 1/2 so you gain that amount as clearance.
Title: Re: Did a short test drive today
Post by: DiDueColpi on February 14, 2011, 03:47:05 PM
Hey Rob,

Really nice sled you've built there!
I'd be talking to Jim about his airbag setup before changing that beautifull stance that your car has.

Cheers
Fred
Title: Re: Did a short test drive today
Post by: denvermgb on February 14, 2011, 07:09:14 PM
Rob,

Lookin' good!

Brad
Title: Re: Did a short test drive today
Post by: MGBV8 on February 14, 2011, 07:30:06 PM
Rob, tuck your exhaust a bit tighter to the body. Jim's ovalized pipe is a great idea. You can also buy it already squashed.  ;)

How do you measure when the chrome strip is missing?  Eyball it or masking tape? Measuring from the center of the axle to the bottom of the chrome strip, my MG is 13.25 front & 14.25 rear.  I rarely drag on anything, so I'm going down another 3/4 to 1" in the front & about 1.5" in the rear.  :-)
Title: Re: Did a short test drive today
Post by: ex-tyke on February 14, 2011, 10:09:51 PM
QuoteI rarely drag on anything

Had a bad experience once when I ran over a dead raccoon at night - made a helluva mess underneath. So, I now know that a dead raccoon is larger than my 4-1/2" min clearance.
Gotta have lots of roadkill in Tennessee, Carl.
Title: Re: Did a short test drive today
Post by: mgb260 on February 14, 2011, 10:19:51 PM
Good one,Graham!
Title: Re: Did a short test drive today
Post by: danmas on February 14, 2011, 11:11:45 PM
Quote from: ex-tykeGotta have lots of roadkill in Tennessee, Carl

I've shredded two ground hogs so far. They were alive when I hit them, not so much so afterwards.
Title: Re: Did a short test drive today
Post by: cgill on February 15, 2011, 12:11:28 AM
WOHOOOOOO!!!

Looks fantastic Rob. I love the stance of the car as it is right now. Great work.
Title: Re: Did a short test drive today
Post by: rficalora on February 15, 2011, 12:18:54 AM
I'm a little lower than I thought...  I measured from center of hubs to the bend where the top of the chrome would be... Probably an extra 1/2" lower than I'd noted earlier based on that. Easy to adjust so that's what I'm going to do 1st.
Title: Re: Did a short test drive today
Post by: ex-tyke on February 15, 2011, 09:54:57 AM
Quote...Easy to adjust so that's what I'm going to do 1st.

Rob, height adjustment is a good thing to have.....new suspensions tend to do some settling over the years.
I fact this Winter while I had my ' 1" lower coil springs'  out, I happen to measure them vs new - they had settled over 3/8" which translates into a 1/2" to 5/8" drop in ride height.
Title: Re: Did a short test drive today
Post by: mgb260 on February 15, 2011, 01:48:41 PM
Rob, have you thought about leaving the bumpers off and putting a rubber strip in front and small quick jack Cobra style bumperettes front and back. I'm thinking about making some to fit the MGB if there is any interest. Picture of Cobra "quick jack" bumperettes:
11880csx2137.jpg
Title: Re: Did a short test drive today
Post by: MGBV8 on February 15, 2011, 05:51:04 PM
Graham,

Hit 'em with the tires. That way you go over instead of them getting stuck under the car.   :-)
Title: Re: Did a short test drive today
Post by: britcars on February 15, 2011, 08:00:15 PM
Rob, great looking car!  Paint, tires, wheels,flare all come together.  Hope to see you and your car in Townsend.
Title: Re: Did a short test drive today
Post by: 74ls1tr6 on February 16, 2011, 07:22:30 AM
Rob,

I had to raise the front of my 6 after intalling 1" lowering springs. The first time going down the curb, my tires rubbed so hard that the car almost wouldn't move. Installed 3/4" spacers, the car sits level now + rolled the fender lip in for more clearance. I'm running 245 tires so that is alot of my problem.

As for your ride! "The stance couldn't look any better". I would try to get the clearance in the exhaust worked out.

Post some photos after you raise your ride for us all to see!

After the meet you can deal with the exhaust later if you like where it is now!  You may want to just keep a higher ride for less worries as Bill stated.

"Looking real good Rob"
Title: Re: Did a short test drive today
Post by: rficalora on February 16, 2011, 08:04:51 AM
Thanks guys.  I raised the car up a bit.  Will ultimately need to adjust the exhaust to get it tighter.  I wanted to avoid that because I had the entire exhaust coated...  modifying will likely mean having to redo it.  It didn't look like it was hanging too low at the time but it must not have been at ride height at the exhaust shop.  Anyway, for now I have about 4" of clearance & will deal with it.  Gonna focus on the brake master so I can drive it.
Title: Re: Did a short test drive today
Post by: classic conversions on February 16, 2011, 01:55:50 PM
It looks great Rob. congrats.Who makes those wheels.
Great stance.
Title: Re: Did a short test drive today
Post by: flitner on February 16, 2011, 02:07:15 PM
I'm looking to do the Quick jack style, has anyone else done it to their B? My friend around the block had suggested using them awhile back and so far this is the second time I've seen them in a picture of an AC. I'm trying to figure out the best way to mount and keep them from twisting over. I have the rear bumper bracket studs set to stick out the rear rolled pan.

Sorry for the Thread Hijack Rob.
Title: Re: Did a short test drive today
Post by: mgb260 on February 16, 2011, 02:18:35 PM
Hey John, I plan on 3/8" flat bar through the bumper slots and just copying the Cobra shape and size,also 3/8". Rear would be slotted like front and flat bar also. Top part would be a bit shorter,wider,no angle. Mounting with  2  5/8" grade 8 bolts and nuts straight through flat bar. Here are some good photos of Stainless Steel ones. Notice these are mounted backwards from the other one, I think it looks better this way. Would also look good just painted black or silver.
DSC01862_Large_.jpg
DSC01864_Large_.jpg