Owner: Dave B
City: CT
Car Model: 1959 AH Sprite
Engine: 1987 Mazda RX-7 13B Rotary
Engine: 1987 Mazda RX-7 13B Rotary
Cooling: Griffin 3" thick Drag Radiator, Perma Cool Puller E-fan, Mazda RX-7 Oil Cooler
Exhaust: Homemade 2" Header heat wrapped and ceramic coated
Transmission: 1987 Mazda RX-7 5 speed
Rear Axle: Stock Housing with competition diff and half-shafts, with dual hub bearings.
Front Susp.: 1965 Midget A-arms, spindles, hubs, with 1275 springs
Rear Susp.: Stock
Brakes:
(master) 1965 Midget
(front) 1965 Midget discs and calipers
(rear) Stock
Wheels/Tires: Stock
Body Mods: Convertible
Interior: Custom
Electrical: American Wiring
Home Coming. Fall of 2007.
gramma011.JPG
gramma010.JPG
gramma003.JPG
I first attacked the Body
Graduation1son003.JPG
Graduation1son005.JPG
Graduation1son002.JPG
I then went in search of a Motor and found a 1987 Mazda Rotary
sunset334.JPG
sunset335.JPG
sunset309.JPG
sunset336.JPG
Next during the winter I stripped and polish and built motor and tranny
motor002.JPG
motor003.JPG
astuff002.JPG
ROTARY008.JPG
Spring 2008 finally came and it was now time to fit this set-up together!
sunset147.JPG
sunset149.JPG
sunset145.JPG
sunset343.JPG
First I attached the tranny!
sunset152.JPG
sunset154.JPG
sunset156.JPG
sunset188.JPG
Next Came the Motor!
sunset160.JPG
sunset168.JPG
sunset173.JPG
Once I had found all the hits I had to perform the following structural modifications!
lights030.JPG
lights033.JPG
lights043.JPG
sunset186.JPG
sunset184.JPG
sunset190.JPG
Once I got the proper clearances I had to add a horizontal stiffener and make a under pan motor mount pad and Tranny mount!
SANY1225.JPG
SANY0781.JPG
Mount.JPG
bugeye007.JPG
SANY1222.JPG
lights008.JPG
Once all that was done I clean up the engine compartment and populated the engine.
bi007.JPG
bi006.JPG
RSintake011.JPG
RSintake002.JPG
Next I had to make a 24" drive shaft. I used a RX-7 drive shaft for tranny interface and it turns out a Ford ranger diff flange and U joint worked great for the rear-end interface.
shaft.JPG
shafted003.JPG
shafted004.JPG
shafted005.JPG
With the Drive train complete I turned my attention to the dreaded Electrical! Yuck!
SANY1139.JPG
SANY1141.JPG
SANY1148.JPG
SANY1188.JPG
SANY1189.JPG
SANY1178.JPG
SANY1195.JPG
shafted001.JPG
SANY1190.JPG
I took a break from the electrical and worked on some interior stuff, replacement tunnel, pedals, dash etc.
tunnel003.JPG
interior.JPG
LaurelaiMae004.JPG
Back to the electrical, this time lights.
LaurelaiMae003.JPG
LaurelaiMae001.JPG
lights069.JPG
With the Electrical done it was time to tackle the cooling, then I could fire it up!!!!!!!!!
First was the oil cooler pretty straight forward!
oilcooler001.JPG
Next was the radiator, what a nightmare this was.
coolnIII001.JPG
coolnIII002.JPG
coolnII001.JPG
Next was the Hoses and E-fan!
coolnIII006.JPG
coolnIII007.JPG
coolnIII005.JPG
NOW IT WAS TIME TO START! Here's a video of the first start-up!!!!!!!!!!
Now that it starts, it was time to roll it out and have a look see !
guns017.JPG
guns01818.JPG
The above 70 something photo's represent 2-1/2 years of work and bring you update to date on this project. Currently I'm working on a disc brake upgrade, front sway bar mod and complete brake system rebuild!
Abrakes001.JPG
Abrakes003.JPG
A-arms003.JPG
A-arms002.JPG
I finally got the new springs. I went with the taller 1275 springs since the upper fender well had rub marks already and them 984 springs might not like the heavier 5 speed tranny, front suspension, and big rad filled with water. I hope it's not to stiff!
A-armsspring001.JPG
Well I got the springs in and man IT WAS NOT EASY!
A-armsp001.JPG
A-armsp002.JPG
I installed the sway bar assembly today and this completes the front end conversion!!! Happy 4th!!!!!!
Alldone002.JPG
Alldone001.JPG
Got away from the front for awhile. I located gauge in cock pit and installed the exhaust system!
A1004.JPG
A1005.JPG
A1006.JPG
Well now it's on to the read brakes. I'm just going to do a rebuild on the stockers until I complete a future rear-end swap-out.
Brakestuff001.JPG
Brakestuff002.JPG
Side one Done!
Brakestuff004.JPG
All brakes and lines are is. Not much more to do as you can see on my white board.
Brakestuff005.JPG
Brakestuff007.JPG
Brakestuff008.JPG
Finally got all the brake lines bleed. Had some issues with the hydraulic clutch, seems the AH master cylinder and the Mazda slave cylinder were not match properly. I need to use a larger Mazda pick-up slave cylinder to get the proper pedal stroke. Also had some binding in the front end. I assembled the new front end with the car on the jack stands. I had to drop it down and loose all the bolts and re-tighten with car on the ground. All is good now. I should be able to take it down the driveway this weekend! I'll add a video link this weekend if all goes well! Wish me luck!
Well it worked out, I took it up and down the drive under it's own power:
T-0Wehaveliftoff002.JPG
T-0Wehaveliftoff003.JPG
T-0Wehaveliftoff004.JPG
Well after much debate I've decided on a color and finish. I'm going with a light blue and a matted finish. I'm also going to add a black rally sprite to match the top and tie in the black under the hood and cockpit. I should have it done in a few weeks and will post some pictures when it's done. That pretty much leaves the interior last on my list. I'll decide what to do with it once it's painted and I can get a feel for the best color combo!
First road test Video!
Finally the first road test. After some issues I finally got it to run good. The thing scary fast and rev's to the moon. I had a sticky apex seal or two and could not get it to rev over 3500 without it stumbling and bogging. I removed the plugs and work each seal back and forth with an unsharpened pencil while spraying the seal directly with carb cleaner. Once I did this to all seals I then work them again with my pencil and this time sprayed each seal with marvel oil and let them sit over night. The next morning I tried to start it and nothing!!! I removed the plugs and they were found with all the junk I sprayed in there. I cleaned them up and BAM fired right up. and sounded good. I can now move on to paint. I like to thank John for all his help. He was able to trouble shoot a car 1,000 miles away and walk me through a pretty frustrating time. Bravo dude!
Fixns003.JPG
Well I melted the 20 gauge piping I used for the header. I now will build a new one from .125 thk wall and see what happens. I bought this batch of stuff on E-bay.
020.JPG
What a winter, I just got around to checking on the car, all is well and my first priority is paint!
All legal now and just waiting on some more $$$$$$$ to get her painted!
SANY2221.JPG
Got some paint and working on interior!
tn_full_SANY2456.jpg
I finally snapped an axle, time to install the Winner circle axles.
SANY2530.JPG
Finally going into the paint booth. I decided on a 30% flat racing blues from Hot Rod flatz. Will post once I'm done.
Finally it's all painted!!!!!!!!!!
CAM001372.jpg
CAM00141.jpg
CAM00144.jpg
CAM001472.jpg
c